Bosch GSL 2f - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

1 609 92A 0L2 | (3.6.14)

Assembly

Power Supply of the Surface Laser

The measuring tool can either be operated with commercially 
available batteries or with a Bosch lithium ion battery pack.

Operation with Batteries (see figure B)

Alkali-manganese batteries are recommended for the meas-
uring tool.

For installation and removal of the batteries, the measuring 
tool’s height adjustment must be set to the lowest position. 
For this, turn the thumbwheel for height adjustment 

9

 in anti-

clockwise direction to the stop.

To open the battery lid 

7

, press on the latch 

6

 and fold the bat-

tery lid up. Insert the batteries. When inserting, pay attention 
to the correct polarity according to the representation on the 
inside of the battery lid.

Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.



Remove the batteries from the measuring tool when 
not using it for extended periods. 

When storing for ex-

tended periods, the batteries can corrode and self-dis-
charge.

Operation with Battery Pack (see figure C)



Use only original Bosch lithium ion battery packs with 
the voltage listed on the nameplate of your measuring 
tool. 

Using other battery packs can lead to injuries and 

pose a fire hazard.

Note: 

Use of battery packs not suitable for the measuring tool 

can lead to malfunctions of or cause damage to the measuring 
tool.

Note: 

The battery pack is supplied partially charged. To en-

sure full capacity of the battery pack, completely charge the 
battery pack in the battery charger before using for the first 
time.



Use only the battery chargers listed on the accessories 
page. 

Only these battery chargers are matched to the lith-

ium-ion battery pack that can be used in your measuring 
tool.

The Lithium-Ion battery pack can be charged at any time with-
out reducing its service life. Interrupting the charging proce-
dure does not damage the battery pack.

The battery pack is equipped with a NTC temperature control 
which allows charging only within a temperature range of be-
tween 0 ° C and 45 ° C. A long battery pack service life is 
achieved in this manner.

For installation and removal of the battery pack 

23

, the meas-

uring tool’s height adjustment must be set to the lowest posi-
tion. For this, turn the thumbwheel for height adjustment 

9

 in 

anticlockwise direction to the stop.

To insert the battery pack 

23

, press on the latch 

6

 and fold the 

battery lid 

7

 up. Slide the charged battery pack completely in-

to the battery compartment and close the battery lid.

Operation with 1,5 Ah battery pack:

In order to shut the 

battery lid 

7

, the foam damper on the inside of the battery lid 

must be removed.

To remove the battery pack 

23

, press on the latch 

6

 and fold 

the battery lid 

7

 up. Pull the battery pack out of the battery 

compartment.

Battery Status Indicator

The three green LEDs of battery status indicator 

5

 indicate the 

charge condition of the batteries or the battery pack 

23

.

Power Supply of the Remote Control (GSL 2 Set)

Using alkali-manganese batteries is recommended for opera-
tion of the remote control.

To open the battery lid 

20

, press on the latch 

21

 and remove 

the battery lid. Insert the batteries. When inserting, pay atten-
tion to the correct polarity according to the representation on 
the inside of the battery lid.

Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.



Remove the batteries from the remote control when 
not using it for longer periods. 

When storing for longer 

periods, the batteries can corrode and discharge them-
selves.

Operation

Starting Operation of the Surface Laser



Protect the measuring tool against moisture and direct 
sun light.



Do not subject the measuring tool to extreme tempera-
tures or variations in temperature. 

As an example, do 

not leave it in vehicles for a long time. In case of large vari-
ations in temperature, allow the measuring tool to adjust to 
the ambient temperature before putting it into operation. 
In case of extreme temperatures or variations in tempera-
ture, the accuracy of the measuring tool can be impaired.



Avoid hard knocks to the measuring tool or dropping it. 

Damaging the measuring tool can cause accuracy to be 

Remote Control

RC 2

Article number

3 601 K69 C00

Working range

2)

20 m

Operating temperature

– 10 ° C ... + 50 ° C

Storage temperature

– 20 ° C ... + 70 ° C

Batteries

3 x 1.5 V LR03 (AAA)

Weight according to 
EPTA-Procedure 01/2003

50 g

2) The working range can be decreased by unfavourable environmental 
conditions (e. g. direct sun irradiation).

For clear identification of your remote control, see the serial number 

22

on the type plate.

LED

Capacity

Continuous lighting 3 x green

≥

2/3

Continuous lighting 2 x green

≥

1/3

Continuous lighting 1 x green

< 1/3

Flashing light 1 x green

Reserve

OBJ_BUCH-1545-006.book  Page 15  Tuesday, June 3, 2014  4:54 PM