Liebherr CBNPes 3976 Premium - Инструкция по эксплуатации - Страница 5

WARNING

Fire hazard due to refrigerant!

The  refrigerant  R  600a  is  environmentally  friendly  but  flam-

mable. Escaping refrigerant may ignite.

u

Do not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

u

Do  not  place  appliances  emitting  heat  e.g.  microwaves,

toasters etc. on the appliance!

WARNING

Blocked ventilation openings pose a risk of fire and damage!

u

Always  keep  the  ventilation  openings  clear.  Always  ensure

that the appliance is properly ventilated!

u

Detach the connecting cable from the rear of the appliance,

removing  the  cable  holder  at  the  same  time  because  other-

wise there will be vibratory noise!

u

Remove  the  protective  film  from  the  outside  of  the  appli-

ance.

NOTICE

The  stainless  steel  doors  are  provided  with  a  high-quality

surface  coating  and  must  not  be  treated  using  the  accompa-

nying care product.

Otherwise the surface coating will be affected. 

u

Wipe  the  coated  door  surfaces  using  a  soft,  clean  cloth

only.

u

Apply  a  stainless  steel  cleaner  only  to  the  stainless  steel

side  walls  evenly,  wiping  with  the  grain.  Subsequent

cleaning becomes easier as a result.

u

Wipe  side  walls  with  a  paint  finish  using  a  soft,  clean

cloth only.

u

Remove all transit supports.

u

Dispose of packaging material (see 4.5) .

NOTICE

Risk of damage due to condensate!

u

Do  not  install  the  appliance  directly  alongside  a  further

refrigerator/freezer.

u

Align  the  appliance  so  that  it

stands firmly and on a level by

applying  the  accompanying

spanner  to  the  adjustable-

height  feet  (A)  and  using  a

spirit level.

u

Then support the door: Extend

the  adjustable  foot  at  the  turn

hinge  (B)  until  it  rests  on  the

floor  and  then  make  a  further

90° turn.

Note

u

Clean the appliance (see 6.2) .

If  the  appliance  is  installed  in  a  very  damp  environment,

condensate may form on the outside of the appliance.

u

Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.
Ensure that the following tools are to hand:

q

Torx® 25

q

Torx® 15

q

Screwdriver

q

Cordless screwdriver, if necessary

q

Second person for fitting work, if needed

4.3.1 Releasing the cable connection on the

housing

Fig. 4 

u

Open the upper door, if necessary.

u

To  remove  the  cover  on  the

handle  side

  Fig.  5  (6):  disen-

gage  using  a  screwdriver  on

the right and slide outwards.

u

To  remove  the  cover  on  the

hinge  side

  Fig.  5  (11):  disen-

gage  using  a  screwdriver  on

the left and slide outwards.

Fig. 5 

u

Remove the front panel

 Fig. 4 (10) using a flat-blade screw-

driver.

u

Take  out  the  contact  and  disconnect  the  plug  connection

Fig. 4 (12).

u

Detach grey cable

 Fig. 4 (13) from the guide.

4.3.2 Detaching the upper door

Note

u

Remove  any  food  from  the  door  racks  before  removing  the

door, so that no food falls out.

Fig. 6 

u

Draw the cover

 Fig. 6 (20) forwards and lift it off.

u

Lift off the cover

 Fig. 6 (21).

Putting into operation

5