Briggs&Stratton Elite 8500 EA 030722 - Инструкция по эксплуатации - Страница 7

Not for 

Reproduction

 7

Step 3: Generator Start up   Figure

1

Disconnect all electrical loads from the generator. Use 

the following start instructions:

  1.  Make sure unit is outdoors on a level surface.

NOTICE

 Failure to operate the unit on a level surface 

may cause the unit to shut down.

  2.  Rotate fuel valve (

R

) to ON (I) position.

  3.  Move choke lever (

P

) to CHOKE ( ) position.

NOTICE

 For a warm engine, be sure choke lever is in 

RUN ( ) position.

  4.  Turn and hold key in start switch (

B

) to START 

( ) 

position until generator starts. DO NOT hold key in 

START 

( )

 position for more than 5 seconds. Pause 

for at least 30 seconds between starting attempts.

NOTICE

 If battery is discharged, turn key in start switch 

to RUN (I) position, grasp recoil handle and pull slowly 

until slight resistance is felt. Then pull rapidly one time 

only to start engine.

  5.  As engine warms up, slowly move choke lever to 

RUN ( ) position.

NOTICE

 This unit is equipped with a low oil protection 

device. Oil must be at proper level for engine to run. If 

the engine oil drops below a preset level, an oil switch 

will stop the engine. Check oil level with dipstick.

WARNING!

   Exhaust heat / gases could 

ignite combustibles, structures or 

damage fuel tank causing a fire, resulting 

in death or serious injury. Contact with muffler area could 

cause burns resulting in serious injury. Pay attention to 

the warnings on the generator. Do not touch hot parts 

and avoid hot exhaust gases. 

Step 4: Connecting Electrical Loads   Figure

1

Generator may only be loaded up to rated power under 

the rated conditions as shown on unit data tag. Reduce 

load when using generator outside of rated conditions.

Use only high quality, well-insulated extension cables in 

accordance with IEC 245-4 with the generator’s 230 Volt 

AC outlets. Inspect extension cables before each use. 

Check that all extension cables are suitably rated and 

are not damaged. When using extension cords under 40° 

C, the total length of cords for a cross section of 1.5 mm² 

should not exceed 50 m or for a cross section of 2.5 mm² 

should not exceed 80 m.

WARNING! 

  Damaged or overloaded extension 

cords could overheat, arc, and burn resulting in 

death or serious injury. Electrical equipment, 

including cables and plug connections, should not be 

defective. 

NOTICE

 Connect electrical loads in off position then 

turn on for operation. 

230 Volt AC Receptacle

Use receptacles (

E

 or 

F

) to operate 230 Volt AC, single-

phase, 50 Hz electrical loads. The 16A receptacles 

are protected against overload by push-to-reset circuit 

breakers (

G

). The 32A receptacle is protected against 

overload by the main breaker (

C

). If the main breaker 

trips, it cuts power to all receptacles.

Protection of electrical components depends on circuit 

breakers specifically matched to the generator. Replace 

circuit breaker with identical rating and performance 

characteristics.

WARNING! 

  Generator voltage could cause 

electrical shock or burn resulting in death or 

serious injury. Do not touch bare wires or 

receptacles. Do not use generator with electrical cords 

which are worn, frayed, bare or otherwise damaged. Do 

not operate generator in the rain or wet weather. Do not 

handle generator or electrical cords while standing in 

water, while barefoot, or while hands or feet are wet. Do 

not allow unqualified persons or children to operate or 

service generator. Keep children a safe distance from 

generator.

Step 5: Generator Shut Down

  1.  Turn off and unplug all electrical loads from generator 

panel receptacles. Never  stop engine with electrical 

devices plugged in and turned on.

  2.  Let engine run at no-load for one minute to stabilize 

internal temperatures of engine and generator.

  3.  Turn key in start switch to OFF (0) position.

  4.  Rotate fuel valve to OFF (0) position.