STIGA COMBI 53 SVQ H 2L0537838/ST1 - Инструкция по эксплуатации - Страница 36

EN - 4

5.3. 

START-UP AND WORK

 NOTE 

  Start the machine on a level surface free from obsta-

cles or grass. 

• 

Models with manual starter hand grip (Fig. 14).

• 

Models with push-button electric starter control (Fig. 15).

 IMPORTANT 

  Always  maintain  a  safe  distance  from  the  cut

-

ting  device  while  working,  corresponding  to  the  length  of  the 

handle.

Emptying the grass catcher

(Fig. 16)

1. 

Release the operator presence lever and wait for 

the cutting device to stop.

2. 

Lift  the  rear  discharge  guard,  take  hold  of  the 

handle and remove the grass catcher by holding 

it in an upright position.

5.4.  STOP

When you have finished working, release the engine brake 

lever/cutting device (Fig. 17).

When you have stopped the machine, it will take 

a few seconds for the cutting means to stop.

Do not touch the engine after it has been turned 

off. Burn hazard.

5.5.  AFTER OPERATION

• 

Cleaning procedure (Par. 5.1).

• 

If  necessary,  replace  the  damaged  components  and 

tighten any loose screws and bolts.

Whenever you leave the machine unused or unattended:

• 

Remove  the  spark  plug  cap  (for  manual  starter  hand 

grip models).

• 

Press  the  tab  and  remove  the  consent  key  (on  models 

with a push-button electric starter).

6. 

MAINTENANCE

The safety regulations to follow are described in chap. 1. Strictly 

comply with these indications to avoid serious risks or dangers.
Before conducting any inspections, cleaning or maintenance/

adjustment interventions on the machine:

• 

Stop the machine.

• 

Make  sure  that  every  moving  component  has  come  to 

a standstill.

• 

Wait for the engine to cool down.

• 

Remove the spark plug cap.

• 

Remove the safety key or the battery on models with a 

push-button electric starter control).

• 

Use suitable clothing, protective gloves and goggles.

6.1.  CLEANING

Clean thoroughly following the instructions below every time 

it is used.

• 

Wash the machine with water after each cut

• 

Remove grass debris and mud accumulated inside the 

chassis.

• 

Always make sure the air intakes are free of debris.

• 

Do not use aggressive liquids to clean the chassis.

• 

To reduce the risk of fire, keep the engine free of grass 

mulch, leaves or excessive grease.

6.2.  CUTTING MEANS MAINTENANCE

All  work  on  the  cutting  means  (disassembly, 

sharpening, balancing, repairing, reassembly 

and/or replacing) are demanding jobs that require 

special skills as well as special tools. For safety 

reasons,  these  jobs  are  best  carried  out  at  a 

Specialised Centre.

Make sure damaged, misshapen or worn cutting-

means are replaced, together with its own screws 

in place to preserve balance.

 IMPORTANT 

  Always  use  original  cutting  devices  with  the 

code shown in the "Technical Data" table.

6.3.  RECHARGE THE BATTERY

The battery is supplied for electric push-button starter switch 

models. Read the engine instruction manual for instructions 

regarding autonomy, recharging, reinstating and  maintenance 

of the battery.

 NOTE 

  For more information on maintenance, please refer to 

the full instruction manual.

7. 

TRANSPORT, STORAGE AND 

DISPOSAL

7.1.  TRANSPORT

Whenever the machine is to be handled, raised, transported 

or tilted you must:

• 

Stop the machine.

• 

Make  sure  that  every  moving  component  has  come  to 

a standstill.

• 

Remove the spark plug cap or remove the safety key or 

battery  (on  models  with    a  push-button  electric  starter 

control).

• 

Wear heavy work gloves.

• 

Hold the machine in the points offering a safe grip, taking 

into account the weight and its division.

• 

Use an adequate number of people suitable to the weight 

of the machine.

• 

Make sure that machine movements do not cause damage 

or injuries.

• 

Fasten  firmly  to  the  means  of  transport  using  ropes  or 

chains  to  prevent  it  from  tipping  over  causing  damage 

and fuel leaks.

7.2.  STORAGE

When the machine is to be stored away:

• 

Start  the  engine  in  the  open  air  and  run  it  idle  until  it 

comes to a halt, so that it uses up all the fuel that is left 

in the carburettor.

• 

Clean the machine thoroughly.

• 

Check the integrity of the machine;

Store the machine:

• 

In a dry place.

• 

Protected from inclement weather.

• 

In a place not accessible to children.

• 

Making  sure  that  keys  or  tools  used  for  maintenance 

are removed.

 NOTE 

  The  machine  must  be  stored  safely  and  securely  to 

prevent  any  accidental  or  unwanted  contact  with  people,  chil

-

dren or animals.