Husqvarna LC 356VP - Инструкция по эксплуатации - Страница 10

To set the product in operation position

1. Fold the handle to upright position. (Fig. 15)
2. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 13)

3. Tighten the knobs fully.
4. Attach the battery to the engine (LC 153S).

To assemble the grass catcher (LC

153P, LB 256S, LC 356VP)

1. Attach the grass catcher frame to the grass bag with

the rigid part of the bag on the bottom. Keep the

handle of the frame out of the top of the bag. (Fig.

16)

2. Attach the grass bag to the frame with the clips. (Fig.

17)

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

Husqvarna Connect

Husqvarna Connect is a free app for your mobile device.

The Husqvarna Connect app gives extended functions

for your Husqvarna product:
• Extended product information.
• Information about, and help with, product parts and

servicing.

To start to use Husqvarna Connect

1. Download the Husqvarna Connect app on your

mobile device.

2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect

app to connect and register the product.

Before you operate the product

1. Read the operator's manual carefully and make sure

that you understand the instructions.

2. Examine the cutting equipment to make sure that it

is correctly attached and adjusted. See 

To examine

the cutting equipment on page 12.

3. Fill the fuel tank. See 

To fill fuel on page 10.

4. Fill the oil tank and do a check of the oil level. See 

To do a check of the oil level on page 13.

To fill fuel

If available, use low-emission/alkylate gasoline. If low-

emission/alkylate gasoline is not available, use good

quality unleaded gasoline or leaded gasoline with octane

number not less than 90.

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

1. Open the fuel tank cap slowly to release the

pressure.

2. Fill slowly with a fuel can. If you spill fuel, remove it

with a cloth and let remaining fuel dry off.

3. Clean the area around the fuel tank cap.
4. Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

5. Move the product a minimum of 3 m (10 ft) from the

position where you filled the tank before a start.

To set the cutting height

1. Move the cutting height lever rearward to increase

the cutting height.

2. Move the cutting height lever forward to decrease

the cutting height. (Fig. 18)

CAUTION: Do not set the cutting height too

low. The blades can hit the ground if the

surface of the lawn is not level.

To start the product

1. Make sure that the ignition cable is connected to the

spark plug.

2. Stay behind the product.
3. Hold the engine brake handle against the handlebar.

(Fig. 19)

4. Hold the starter rope handle with your right hand.
5. Slowly pull out the starter rope until you feel some

resistance.

6. Pull with force to start the engine.

WARNING: Do not twist the starter rope

around your hand.

To use the drive on the wheels (LC

153S, LB 256S, LC 356VP)

• For LB 256S and LC 153S: Push the drive bail in the

direction of the handlebar. (Fig. 20)

• For LC 356VP: Start the drive on the wheels with the

speed control lever on the left side of the handle.

Move the speed control lever forward to increase the

speed and rearward to decrease the speed. (Fig. 21)

10

1227 - 003 - 17.09.2019