DEFORT DLM-1010N 98299311 - Инструкция по эксплуатации - Страница 9

9

GB

3. ASSEMBLY

We recommend assembling the lawnmower in the en-
closed space on an even surface or on a special work-
ing table. You will need a cross-tip screwdriver during 
the assembly. Start the assembly after the identi

fi

 cation 

of all parts (

fi

 g. 1)

 
•  Upon removal of the lawnmower from the box, put 

the lower part of the handle (5) in the apertures of 
the body. Afterwards, lift the cover and fasten the 
ends of the handle in the body with selftapping 
screws from the back side.  

•  Fasten the cable hanger (10) to the upper part of the 

handle (6). 

•  Connect the cable to the lawnmower’s handle with 

two clamps. 

•  Join the upper part of the handle (6) with lower parts 

(5) and fasten thereof with a screw (7) and a nut (8), 
placed into a plastic assembly wrench. 

•  Screw the wheels (11 and 12) on. All wheels should 

be fastened on the same height. 

•  The both parts of the grass reservoir (4) shall be 

pushed into the apertures until hearing a click.

REPLACING THE CUTTING BLADE 

•  Switch off and remove the plug from mains before 

replacing the blade. 

•  Note that the wings of the knife shall be directed up-

wards for fastening. 

• A 

fl

 at or other hexagon spanner of 24 size is used for 

unscrewing and screwing of the blade. 

•  Please note that the head of the screw fastening the 

blade is made from plastic material; accordingly, the 
force applied onto the screw during the 

fi

 xing of the 

blade shall be 10-16 Nm. 

•  Replace the cutting knife with the knife of the type 

speci

fi

 ed only.

4. USE

Operation

The essence of operation of the lawnmower is a hori-
zontally cutting knife fastened to the vertical shaft of the 
motor; the knife, which rotates with a speed of approxi-
mately 3000 r/min. cuts the grass at the preselected 
height. Cut grass is thrown into the bag via an aperture 
in the rear side of the lawnmower under the impact of 
centrifugal force and the pressure resulting from the ro-
tation of the knife. Proper positioning of the knife is of 
great signi

fi

 cance for this process.

Switching ON and OFF (

fi

 g.2)

1. push the round button with one hand
2. draw and hold the switch handle with another hand
3. release the round button
4. hold the switch handle during the entire period of 
lawnmower operation
5. releasing the switch handle will switch off the lawn-
mower 

User tips

Please remember the most important rule for lawn care 
- mow grass instead of plants growing therein. The 
mowing procedure shall be repeated once in two-to-
three days with grass growing again fast. Lawnmower 

•  Before using, always check if the blades, blade bolts 

and cutter assembly are not worn or damaged. Re-
place worn or damaged blades and bolts in sets to 
preserve balance. 

•  On multi-bladed appliances, take care as rotating 

one blade can cause other blades to rotate.

Operation 

•  Mow only in daylight or in good arti

fi

 cial light. 

•  Avoid operating the appliance in wet grass, where 

feasible. 

•  Always be sure of your footing on slopes. 
•  Walk, never run. 
•  For wheeled rotary mowers, mow across the face of 

slopes, never up and down. 

•  Exercise extreme caution when changing direction 

on slopes. 

•  Do not mow excessively steep slopes. 
•  Use extreme caution when reversing or pulling the 

appliance towards you. 

•  Stop the blade(s) if the appliance has to be tilted 

for transportation when crossing surfaces other than 
grass, and when transporting the appliance to and 
form the area to be mowed. 

•  Never operate the appliance with defective guards 

or shields, or without safety devices, for example 
de

fl

 ectors and/or grass catchers, in place. 

•  Switch on the motor according to instructions and 

with feet well away from the blade(s). 

•  Do not tilt the appliance when switching on the mo-

tor, except if the appliance has to be tilted for start-
ing. In this case, do not tilt it more than absolutely 
necessary and lift only the part which is away from 
the operator. Always ensure that both hands are in 
the operating position before returning the appliance 
to the ground. 

•  Do not put hands or feet near or under rotating parts. 

For rotary mowers, keep clear of the discharge 
opening at all times. 

•  Never pick up or carry an appliance while the motor 

is running. 

•  Pull the plug from the socket: 
•  whenever you leave the machine; 
•  before clearing a blockage; 
•  before checking, cleaning or working on the appli-

ance; 

•  after striking a foreign object. Inspect the appliance 

for damage and make repairs as necessary; 

•  if the appliance starts to vibrate abnormally (check 

immediately).

MAINTENANCE AND STORAGE 

•  Keep all nuts, bolts, and screws tight to be sure the 

appliance is in safe working condition. 

•  Check the grass catcher frequently for wear of dete-

rioration. 

•  Replace worn of damaged parts for safety. 
•  For cylinder mowers, be careful during adjustment 

of the appliance to prevent entrapment of the 

fi

 ngers 

between moving blades and 

fi

 xed parts of the appli-

ance. 

•  For rotary mowers, ensure that only replacement 

cutting means of the right type are used.