Makita DUC204Z - Инструкция по эксплуатации - Страница 16

16 ENGLISH

NOTICE:

When filling the chain oil for the first 

time, or refilling the tank after it has been com

-

pletely emptied, add oil up to the bottom edge of 

the filler neck. The oil delivery may otherwise be 

impaired.

NOTICE:

Use the saw chain oil exclusively for 

Makita chain saws or equivalent oil available in 

the market.

NOTICE:

Never use oil including dust and parti-

cles or volatile oil.

NOTICE:

When pruning trees, use botanical oil. 

Mineral oil may harm trees.

NOTICE:

Before the cutting operation, make sure 

that the provided oil tank cap is screwed in place.

WORKING WITH THE CHAIN SAW

CAUTION:

The first time user should, as a 

minimum practice, do cutting logs on a saw-horse 

or cradle.

CAUTION:

When sawing precut timber, use a 

safe support (saw horse or cradle). Do not steady 

the workpiece with your foot, and do not allow 

anyone else to hold or steady it.

CAUTION:

Secure round pieces against 

rotation.

CAUTION:

Keep all parts of the body away 

from the saw chain when the motor is operating.

CAUTION:

Hold the chain saw firmly with 

both hands when the motor is running.

CAUTION:

Do not overreach. Keep proper 

footing and balance at all times.

NOTICE:

Never toss or drop the tool.

NOTICE:

Do not cover the vents of the tool.

Pruning trees

Bring the chain saw body into contact with the branch to 

be cut before switching on. Otherwise it may cause the 

guide bar to wobble, resulting in injury to operator. Saw 

the wood to be cut by just moving it down by using the 

weight of the chain saw.

► 

Fig.19

If you cannot cut the timber right through with a single 

stroke: 

Apply light pressure to the handle and continue sawing 

and draw the chain saw back a little.

► 

Fig.20

When cutting thick branches, first make a shallow 

undercut and then make the finish cut from the top.

► 

Fig.21

If you try to cut off thick branches from the bottom, the 

branch may close in and pinch the saw chain in the cut. 

If you try to cut off thick branches from the top without a 

shallow undercut, the branch may splinter.

► 

Fig.22

Bucking

1.

Rest the chain saw body on the wood to be cut.

► 

Fig.23

2.

With the saw chain running, saw into the wood 

while using the top handle to raise the saw and the front 

one to guide it.

3.

Continue the cut by applying slight pressure to the 

top handle, easing the saw back slightly.

NOTICE:

When making several cuts, switch the 

chain saw off between cuts.

CAUTION:

If the upper edge of the bar is used 

for cutting, the chain saw may be deflected in 

your direction if the chain becomes trapped. For 

this reason, cut with the lower edge, so that the 

saw will be deflected away from your body.

► 

Fig.24

When you cut a wood under tension, cut the pressured 

side (A) first. Then make the final cut from the tensioned 

side (B). This prevents the bar from becoming trapped.

► 

Fig.25

Limbing

CAUTION:

Limbing may only be performed by 

trained persons.

 A hazard is presented by the risk 

of kickback.

When limbing, support the chain saw on the trunk if 

possible. Do not cut with the tip of the bar, as this pres-

ents a risk of kickback. 

Pay particular attention to branches under tension. Do 

not cut unsupported branches from below. 

Do not stand on the felled trunk when limbing.

Carrying tool

Before carrying the tool, always apply the chain brake 

and remove the battery cartridges from the tool. Then 

attach the guide bar cover. Also cover the battery car-

tridge with the battery cover.

► 

Fig.26:

1.

 Guide bar cover 

2.

 Battery cover

MAINTENANCE

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before attempting to perform inspection or 

maintenance.

CAUTION:

Always wear gloves when perform-

ing any inspection or maintenance.

NOTICE:

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.