Makita DUC204Z - Инструкция по эксплуатации - Страница 11

11 ENGLISH

13. 

Before starting work, check that the chain 

saw is in proper working order and that its 

condition complies with the safety regulations. 

Check in particular that:

• 

The chain brake is working properly;

• 

The run-down brake is working properly;

• 

The bar and the sprocket cover are fitted 

correctly;

• 

The chain has been sharpened and ten-

sioned in accordance with the regulations.

14. 

Do not start the chain saw with the chain cover 

being installed on it.

 Starting the chain saw with 

the chain cover being installed on it may cause 

the chain cover to thrown out forward resulting in 

personal injury and damage to objects around the 

operator.

Top handle chainsaw specific safety 

warnings

1. 

This chain saw is designed especially for tree 

care and surgery. The chain saw is intended 

to be used by properly trained persons only. 

Observe all instructions, procedures and rec-

ommendations from the relevant professional 

organization. Otherwise fatal accidents may 

occur. It is recommend that always using a 

rising platform (cherry picker, lift) for sawing 

in trees. Rappelling techniques are extremely 

dangerous and require special training. The 

operators must be trained to become familiar 

with safety equipment usage and climbing 

techniques. Always use the appropriate belts, 

ropes and carabiners when working in trees. 

Always use restraining equipment for both the 

operator and the saw.

2. 

Perform cleaning and maintenance before 

storage in accordance with the instruction 

manual.

3. 

Ensure safe positioning of the chain saw 

during car transportation to avoid fuel or chain 

oil leakage, damage to the tool and personal 

injury.

4. 

Regularly check the functionality of chain 

brake.

5. 

Do not fill the chain oil near fire. Never smoke 

when you fill the chain oil.

6. 

National regulation may restrict the use of the 

chain saw.

7. 

If the equipment gets heavy impact or fall, 

check the condition before continuing work. 

Check the controls and safety devices for mal-

function. If there is any damage or doubt, ask 

our authorized service center for the inspec-

tion and repair.

8. 

Always activate the chain brake before starting 

the chain saw.

9. 

Hold the saw firmly in place to avoid skating 

(skid movement) or bouncing of the saw when 

starting a cut.

10. 

At the end of the cut, be careful to keep your 

balance due to the “drop”.

11. 

Take into account the direction and speed of 

the wind. Avoid sawdust and chain oil mist.

Protective equipment

1. 

In order to avoid head, eye, hand or foot 

injuries as well as to protect your hearing the 

following protective equipment must be used 

during operation of the chain saw:

—  The kind of clothing should be appropriate, i. e. 

it should be tight-fitting but not be a hindrance. 

Do not wear jewelry or clothing which could 

become entangled with bushes or shrubs. If you 

have long hair, always wear a hairnet!

—  It is necessary to wear a protective helmet 

whenever working with the chain saw. The 

protective helmet

 is to be checked in regu-

lar intervals for damage and is to be replaced 

after 5 years at the latest. Use only approved 

protective helmets.

— The 

face shield

 of the protective helmet (or 

the goggles) protects against sawdust and 

wood chips. During operation of the chain 

saw always wear a goggle or a face shield to 

prevent eye injuries.

—  Wear adequate 

noise protection equip-

ment

 (ear muffs, ear plugs, etc.)

— The 

protective jacket

 consists of 22 layers 

of nylon and protects the operator against 

cuts. It is always to be worn when working 

from elevated platforms (cherry pickers, 

lifts), from platforms mounted on ladders or 

when climbing with ropes.

— The 

protective brace and bib overall

 is 

made of a nylon fabric with 22 layers and 

protects against cuts. We strongly recom-

mend its use.

— 

Protective gloves

 made of thick leather are part 

of the prescribed equipment and must always be 

worn during operation of the chain saw.

—  During operation of the chain saw 

safety 

shoes

 or 

safety boots

 fitted with anti skid 

sole, steel toe caps and protection for the 

leg must always to be worn. Safety shoes 

equipped with a protective layer provide 

protection against cuts and ensure a secure 

footing. For working in trees the safety boots 

must be suitable for climbing techniques.

Vibration

1. 

Individuals with poor circulation who are exposed 

to excessive vibration may experience injury to 

blood vessels or the nervous system. Vibration 

may cause the following symptoms to occur in the 

fingers, hands or wrists: “Falling asleep” (numb

-

ness), tingling, pain, stabbing sensation, alteration 

of skin colour or of the skin. 

If any of these symp-

toms occur, see a physician!

 To reduce the risk 

of “white finger disease”, keep your hands warm 

during operation and well maintain the equipment 

and accessories.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.