Makita DUC204Z - Инструкция по эксплуатации - Страница 10

10 ENGLISH

WARNING:

 The vibration emission during actual 

use of the power tool can differ from the declared 

emission value depending on the ways in which the 

tool is used.

WARNING:

 Be sure to identify safety measures 

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking 

account of all parts of the operating cycle such as 

the times when the tool is switched off and when it is 

running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A 

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING:

Read all safety warnings, instruc-

tions, illustrations and specifications provided 

with this power tool.

 Failure to follow all instructions 

listed below may result in electric shock, fire and/or 

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your 

mains-operated (corded) power tool or battery-operated 

(cordless) power tool.

Cordless Chain saw safety warnings

1. 

Keep all parts of the body away from the saw 

chain when the chain saw is operating. Before 

you start the chain saw, make sure the saw 

chain is not contacting anything.

 A moment of 

inattention while operating chain saws may cause 

entanglement of your clothing or body with the 

saw chain.

2. 

Always hold the chain saw with your right 

hand on the top handle and your left hand on 

the front handle.

 Holding the chain saw with a 

reversed hand configuration increases the risk of 

personal injury and should never be done.

3. 

Hold the power tool by insulated gripping 

surfaces only, because the saw chain may con-

tact hidden wiring.

 Saw chains contacting a "live" 

wire may make exposed metal parts of the power 

tool "live" and could give the operator an electric 

shock.

4. 

Wear safety glasses and hearing protection.

Further protective equipment for head, hands, 

legs and feet is recommended. Adequate protec-

tive clothing will reduce personal injury by flying 

debris or accidental contact with the saw chain.

5. 

Always keep proper footing.

6. 

When cutting a limb that is under tension be alert 

for spring back.

 When the tension in the wood fibres 

is released the spring loaded limb may strike the 

operator and/or throw the chain saw out of control.

7. 

Use extreme caution when cutting brush and sap-

lings.

 The slender material may catch the saw chain 

and be whipped toward you or pull you off balance.

8. 

Carry the chain saw by the front handle with 

the chain saw switched off and away from your 

body. When transporting or storing the chain 

saw always fit the guide bar cover.

 Proper 

handling of the chain saw will reduce the likelihood 

of accidental contact with the moving saw chain.

9. 

Follow instructions for lubricating, chain ten-

sioning and changing accessories.

 Improperly 

tensioned or lubricated chain may either break or 

increase the chance for kickback.

10. 

Keep handles dry, clean, and free from oil and 

grease.

 Greasy, oily handles are slippery causing 

loss of control.

11. 

Cut wood only. Do not use chain saw for pur-

poses not intended.

 For example: do not use 

chain saw for cutting plastic, masonry or non-

wood building materials. Use of the chain saw for 

operations different than intended could result in a 

hazardous situation.

12. 

Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the 

guide bar touches an object, or when the wood 

closes in and pinches the saw chain in the cut. 

Tip contact in some cases may cause a sudden 

reverse reaction, kicking the guide bar up and 

back towards the operator. Pinching the saw chain 

along the top of the guide bar may push the guide 

bar rapidly back towards the operator. Either of 

these reactions may cause you to lose control of 

the saw which could result in serious personal 

injury. Do not rely exclusively upon the safety 

devices built into your saw. As a chain saw user, 

you should take several steps to keep your cutting 

jobs free from accident or injury.

Kickback is the result of tool misuse and/or incor-

rect operating procedures or conditions and can 

be avoided by taking proper precautions as given 

below:

• 

Maintain a firm grip, with thumbs and fingers 

encircling the chain saw handles, with both 

hands on the saw and position your body 

and arm to allow you to resist kickback 

forces. Kickback forces can be controlled by 

the operator, if proper precautions are taken. 

Do not let go of the chain saw.

► 

Fig.1

• 

Do not overreach and do not cut above 

shoulder height. This helps prevent unin-

tended tip contact and enables better control 

of the chain saw in unexpected situations.

• 

Only use replacement bars and chains spec-

ified by the manufacturer. Incorrect replace

-

ment bars and chains may cause chain 

breakage and/or kickback.

• 

Follow the manufacturer’s sharpening and 

maintenance instructions for the saw chain. 

Decreasing the depth gauge height can lead 

to increased kickback.