DEFORT DEC-1646N 98291858 - Инструкция по эксплуатации - Страница 10

10

●

  Do not overreach and do not cut above shoulder height. 

This helps prevent unintended tip contact and enables bet-
ter control of the chain saw in unexpected situations.

●

  Only use replacement bars and chains speci

fi

 ed by the 

manufacturer. Incorrect replacement bars and chains may 
cause chain breakage and/or kickback.

●

  Follow the manufacturer’s sharpening and maintenance in-

structions for the saw chain. Decreasing the depth gauge 
height can lead to increased kickback.

●

  Children and juveniles, with the exception of apprentices 

older than 16 years and under supervision, may not oper-
ate the chain saw. The same applies for persons who do 
not or do not suf

fi

 ciently know how to handle the chain saw. 

The operating instructions should al ways be ready to hand. 
Persons un

fi

 t or tired must not operate the chain saw.

●

  Always ensure all handles and guards are 

fi

 tted when using 

the machine. Never attempt to use an incomplete machine 
or one 

fi

 tted with an unauthorized modi

fi

 cation.

●

  When working with the machine, always hold it 

fi

 rmly  with 

both hands and provide for a secure stance. The power tool 
is guided more secure with both hands.

●

  Always wait until the machine has come to a complete stop 

before placing it down. The tool insert can jam and lead to 
loss of control over the power tool. It is recommended that 
the 

fi

 rst time user should have practical instruction in the 

use of the chainsaw and the protective equipment from an 
experienced operator. The initial practice should be cutting 
logs on a saw horse or cradle.

Products sold in GB only: Your product is 

fi

 tted with an BS 

1363/A approved electric plug with internal fuse (ASTA ap-
proved to BS 1362). If the plug is not suitable for your socket 
outlets, it should be cut off and an appropriate plug 

fi

 tted in its 

place by an authorised customer service agent. The replace-
ment plug should have the same fuse rating as the original 
plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains socket 
elsewhere. Products sold in AUS and NZ only: Use a residual 
current device (RCD) with a rated residual current of 30 mA 
or less.

PRODUCT DESCRIPTION AND 
SPECIFICATIONS

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in 
electric shock, 

fi

 re and/or serious injury.

While reading the operating instructions, unfold the graphics 
page for the machine and leave it open.

INTENDED USE

The power tool is intended for sawing wood such as wooden 
beams, planks, branches, tree trunks, etc., and for sawing of 
trees. Cuts can be sawed with or across the grain.

OPERATION

Starting Operation

●

  Observe the mains voltage! The voltage of the power 

source must correspond with the data on the type plate of 
the machine.

SWITCHING ON AND OFF

Hold the chain saw as described in section “Working with the 
Chain Saw”.
To start the machine, 

fi

 rst push the lock-off button for the On/

Off switch 2 and then press the On/Off switch 3 and keep it 
pressed.
To switch off the machine, release the On/Off switch 3.
Note: For safety reasons, the On/Off switch 3 cannot be locked; 
it must remain pressed during the entire operation.
Note: Do not stop chain saw after sawing by actuating the front 
hand guard 5 (activating the kickback brake).

CHAIN SAW SAFETY WARNINGS

●

  Keep all parts of the body away from the saw chain when 

the motor is operating. Before you start the chain saw, make 
sure the saw chain is not contacting anything. A moment of 
inattention while operating chain saws may cause entangle-
ment of your clothing or body with the saw chain.

●

  Always hold the chain saw with your right hand on the rear 

handle and your left hand on the front handle. Holding the 
chain saw with a reversed hand con

fi

 guration increases the 

risk of personal injury and should never be done.

●

  Hold the power tool by insulated gripping surfaces only, 

because the saw chain may contact hidden wiring or its 
own cord. Saw chains contacting a “live” wire may make 
exposed metal parts of the power tool “live” and could give 
the operator an electric shock.

●

  Wear safety glasses and hearing protection. Further pro-

tective equipment for head, hands, legs and feet is recom-
mended. Adequate protective clothing will reduce personal 
injury by 

fl

 ying debris or accidental contact with  the saw 

chain.

●

  Do not operate a chain saw in a tree. Operation of a chain 

saw while up in a tree may result in personal injury.

●

  Always keep proper footing and operate the chain saw only 

when standing on 

fi

 xed, secure and level surface. Slippery 

or unstable surfaces such as ladders may cause a loss of 
balance or control of the chain saw.

●

  When cutting a limb that is under tension be alert for spring 

back. When the tension in the wood 

fi

 bres is released the 

spring loaded limb may strike the operator and/or throw the 
chain saw out of control.

●

  Use extreme caution when cutting brush and saplings. The 

slender material may catch the saw chain and be whipped 
toward you or pull you off balance.

●

  Carry the chain saw by the front handle with the chain saw 

switched off and away from your body. When transporting or 
storing the chain saw, always 

fi

 t the guide bar cover. Proper 

handling of the chain saw will reduce the likelihood of ac-
cidental contact with the moving saw chain.

●

  Follow instructions for lubricating, chain tensioning and 

changing accessories. Improperly tensioned or lubricated 
chain may either break or increase the chance for kickback.

●

  Keep handles dry, clean, and free from oil and grease. 

Greasy, oily handles are slippery causing loss of control.

●

  Cut wood only. Don’t use chain saw for purposes not intend-

ed. For example: do not use chain saw for cutting plastic, 
masonry or non-wood building materials. Use of the chain 
saw for operations different than intended could result in a 
hazardous situation.

CAUSES AND OPERATOR PREVENTION OF 
KICKBACK:

– Kickback may occur when the nose or tip of the guide bar 
touches an object, or when the wood closes in and pinches the 
saw chain in the cut.
– Tip contact in some cases may cause a sudden reverse reac-
tion, kicking the guide bar up and back towards the operator.
– Pinching the saw chain along the top of the guide bar may 
push the guide bar rapidly back towards the operator.
– Either of these reactions may cause you to lose control of 
the saw which could result in serious personal injury. Do not 
rely exclusively upon the safety devices built into your saw. As 
a chain saw user, you should take several steps to keep your 
cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect operating 
procedures or conditions and can be avoided by taking proper 
precautions as given below:

●

 Maintain a 

fi

 rm grip, with thumbs and 

fi

 ngers encircling the 

chain saw handles, with both hands on the saw and position 
your body and arm to allow you to resist kickback forces. 
Kickback forces can be controlled by the operator, if proper 
precautions are taken. Do not let go of the chain saw.