Ryobi RCS5140B 5133001859 - Инструкция по эксплуатации - Страница 4

English

2

Ŷ

Always wear safety boots with a good tread (with non-
slip soles). 

Ŷ

Wear non-slip, heavy duty protective gloves. 

Ŷ

Always wear eye protection with side shields marked 
to comply with EN 166 as well as hearing and head 
protection when operating this equipment.

REFUELLING (DO NOT SMOKE!)

Ŷ

To reduce the risk of fire and burn injury, handle fuel 
with care. It is highly flammable.

Ŷ

Mix and store fuel in a container approved for petrol.

Ŷ

Mix fuel outdoors where there are no sparks or flames.

Ŷ

Select bare ground, stop the engine, and allow it to cool 
before refuelling.

Ŷ

Loosen the fuel cap slowly to release pressure and to 
keep fuel from escaping around the cap.

Ŷ

Tighten the fuel cap securely after refuelling.

Ŷ

Wipe spilled fuel from the unit. Move 9 m away from 
refuelling site before starting engine.

Ŷ

Never attempt to burn off spilled fuel under any 
circumstances.

BASIC PRECAUTIONS IN THE CUTTING/WORK AREA

Ŷ

Do not stand on any unstable surface while using your 
chainsaw, that includes ladders, scaffolds, trees, etc.

Ŷ

Do not start cutting until you have a clear work area, 
secure footing, and a planned retreat path from the 
falling tree.

Ŷ

Do not cut from a ladder, this is extremely dangerous.

Ŷ

Use extreme caution when cutting small-size brush 
and saplings because slender material may catch the 
saw chain and be whipped toward you or pull you off 
balance.

Ŷ

When cutting a limb under tension, be alert for spring-
back so that you will not be struck when the tension in 
the wood fibres is released.

Ŷ

Do not operate a chainsaw in a tree unless you have 
been specifically trained to do so.

Ŷ

Beware of the emission of exhaust gases, lubricant mist 
and saw dust.

Ŷ

This product is very noisy when operating, to prevent 
long term hearing damage, wear hearing protection 
and keep other persons 15 m away from the work area. 
Operating similar tools nearby increases risk of injury. 
Take frequent breaks.

Ŷ

Use of hearing protection reduces the ability to hear 
warnings (shouts or alarms). The operator must pay 
extra attention to what is going on in the work area.

Ŷ

Keep bystanders and animals out of the work area. Do 
not allow other persons to be nearby during starting or 
cutting with the chainsaw.

NOTE:

 The size of the work area depends on the job being 

performed as well as the size of the tree or work piece 
involved. For example, felling a tree requires a larger work 

area than making other cuts, i.e., bucking cuts etc.

PUSH AND PULL

The reaction force is always opposite to the direction the 
chain is moving. Thus, the operator must be ready to 
control the pull when cutting on the bottom edge of the bar 
and the push when cutting along the top edge. 

NOTE:

 Your chainsaw has been fully factory tested. It is 

QRUPDOWR¿QGVRPHVOLJKWOXEULFDQWUHVLGXHRQWKHVDZ

MAINTENANCE PRECAUTIONS

Ŷ

Never operate a chainsaw that is damaged, improperly 
adjusted, or is not completely and securely assembled. 

Ŷ

Be sure that the saw chain stops moving when the 
throttle control trigger is released. If the saw chain 
moves at idling speed, the carburettor may need 
adjusting. Refer to “Operation-adjusting idling speed” 
later in this manual. If the saw chain still moves at 
idling speed after adjustment has been made, contact 
a Ryobi service dealer for adjustment and discontinue 
use until the repair is made.

Ŷ

Keep the handles dry, clean, and free of lubricant or 
fuel mixture.

Ŷ

Follow the sharpening and maintenance instructions for 
the saw chain.

Ŷ

Use only the replacement guide bars and low kickback 
chains specified for your saw. You must never modify 
or remove parts from this product or use parts not 
recommended by Ryobi. This will increase the risk of 
injury.

 WARNING

The risk of kickback may increase if non-approved guide 
bar and chain combinations are used. Refer to technical 

VSHFL¿FDWLRQV IRU TXDOL¿HG UHSODFHPHQW JXLGH EDU DQG

chain combinations.  

 WARNING

All chainsaw service, other than the items in the 
operator’s manual maintenance instructions, should be 
performed by competent chainsaw service personnel. 

,I LPSURSHU WRROV DUH XVHG WR UHPRYH WKH À\ZKHHO RU
FOXWFKRULIDQLPSURSHUWRROLVXVHGWRKROGWKHÀ\ZKHHO

in order to remove the clutch, structural damage to the 

À\ZKHHO FRXOG RFFXU ZKLFK FRXOG VXEVHTXHQWO\ FDXVH
WKHÀ\ZKHHOWREXUVWDQGVHULRXVLQMXU\FRXOGUHVXOW

KICK-BACK

Ŷ

Kick-back may occur when the nose of the guide bar 
touches an object or when the wood closes in and 
pinches the saw chain in the cut. The nose of guide 
bar contact in some cases may cause a lightning-fast 
reverse reaction kicking the guide bar up and back 
toward the operator. Pinching the saw chain along the 
top of the guide bar may push the guide bar rapidly