Einhell FORTEXXA 18/30 X-CHANGE аккум. (4600010) - Инструкция по эксплуатации - Страница 25

GB

- 25 -

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(18) into the socket outlet. The green LED will 

then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger.

In section 12 (Charger indicator) you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to charge, check for the 

following:

• 

voltage at the power socket

• 

whether there is good contact at the charging 

contacts of the charging unit

If the battery pack still fails to charge, send

• 

the charger and charging adapter

• 

and the battery pack

to our customer service center.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

5.5 Battery capacity indicator (Fig. 12)

Press the button for the battery capacity indicator 

(C). The battery capacity indicator (D9 shows the 

charge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED 

fl

 ashes:

The battery is empty, recharge the battery.

All LEDs blink:

The battery temperature is too low. Remove the 

battery from the equipment, keep it at room tem-

perature for one day. If the fault reoccurs, this me-

ans that the rechargeable battery has undergone 

exhaustive discharge and is defective. Remove 

the battery from the equipment. Never use or 

charge a defective battery.

6. Operation

6.1 Switching on/o

ff

Switching on

• 

 Plug in the battery on the equipment. 

• 

The respective power level is indicated by two 

colored LED:

Level I (ECO) 

→

 green

Level II (HIGH) 

→

 blue

• 

 To switch between power levels I and II, brief-

ly press the power setting switch (Fig. 1 / Item 

20) 1x.

• 

Hold the chainsaw by the handles with both 

hands as shown in Fig. 13 (thumbs under the 

handles).

• 

 Press and hold the safety lock-off (Fig. 1/Item 

5).

• 

 Switch on the chainsaw at the ON/OFF switch 

(Fig. 1/Item 6). You can then release the safe-

ty lock-off.

Switching o

ff

Release the ON/OFF switch (Fig. 1/Item 6).

The integrated brake will bring the running chain-

saw to a standstill within a very short space of 

time. Always disconnect the mains plug when you 

stop working, even if it is only for a short time.

Warning! 

Always carry the saw by the front 

handle. If the saw is plugged in and you carry it by 

the rear handle (which is where the switches are 

located), then there is a risk that you could acci-

dentally press the safety lock-o

ff

  and the ON/OFF 

switch at the same time, and the chainsaw could 

inadvertently start up.

6.2 Safety devices 

Motor brake

The motor brakes the saw chain as soon as the 

ON/OFF switch (Fig. 1/Item 6) is released or the 

power supply is interrupted. This signi

fi

 cantly 

reduces the risk of injury that would otherwise be 

present if the chain continued to run after being 

Anl_Fortexxa_18_30_SPK13.indb   25

19.07.2021   13:57:26