Einhell TC-WD 200/150, 250 Вт (4417242) - Инструкция по эксплуатации - Страница 24

GB

- 24 -

After switching on the equipment wait for the 

equipment to reach its maximum speed of rotati-

on before commencing with the sanding/grinding 

work. 

6.2 Dry grinding

• 

 For coarse grinding it is recommended to use 

the coarse-grained grinding wheel (5).

• 

 Turn on the grinding machine using the ON/

OFF switch (1).

• 

 Place the workpiece onto the workpiece 

support (7) and slowly guide the workpiece 

towards the grinding wheel (5) at the desired 

angle to the point where workpiece and grin-

ding wheel make contact.

• 

 Move the workpiece slightly back and forth to 

produce an optimal grinding result. This way 

the grinding wheel (5) will be evenly worn. Al-

low the workpiece to cool down occasionally.

Caution!

If the grinding/sanding wheel becomes jammed 

during operation, remove the workpiece and wait 

until the tool reaches its top speed again. If ne-

cessary, use less force when moving the workpie-

ce against the grinding/sanding wheel.

6.3 Wet grinding

• 

 For fine grinding it is recommended to use the 

fine-grained grinding wheel (6).

• 

 Check that the sealing plug (21) is fitted befo-

re you start wet grinding.

• 

 In addition, also check that there is enough 

water in the water container (10) (a third of 

the wet grinding wheel (6) must be standing 

in water!).

• 

 Turn on the grinding machine using the ON/

OFF switch (1).

• 

 Grip the workpiece with both hands and lower 

it slowly onto the grinding wheel (6).

• 

 You can also rest the workpiece on the teeth 

on the water container and lower it onto the 

grinding wheel (6).

7.  Replacing the power cable

Danger!

If the power cable for this equipment is damaged, 

it must be replaced by the manufacturer or its 

after-sales service or similarly trained personnel 

to avoid danger.

8.  Cleaning, maintenance and 

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

8.2 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

8.3  Ordering replacement parts:

Please quote the following data when ordering 

replacement parts:

• 

 Type of machine

• 

 Article number of the machine

• 

 Identification number of the machine

• 

 Replacement part number of the part required

For our latest prices and information please go to 

www.isc-gmbh.info

8.4 Transport

Transport the machine only by lifting it by the 

motor housing or by the base plate (9). Never use 

safety devices such as the safety window (2), the 

spark de

fl

 ector (3) or the workpiece support (7) 

for handling or transporting purposes.

Anl_TC_WD_200_150_SPK9.indb   24

Anl_TC_WD_200_150_SPK9.indb   24

23.06.2020   15:30:18

23.06.2020   15:30:18