Einhell TC-WD 200/150, 250 Вт (4417242) - Инструкция по эксплуатации - Страница 22

GB

- 22 -

Keep the noise emissions and vibrations to a 

minimum.

• 

 Only use appliances which are in perfect wor-

king order.

• 

 Service and clean the appliance regularly.

• 

 Adapt your working style to suit the appliance.

• 

 Do not overload the appliance.

• 

 Have the appliance serviced whenever ne-

cessary.

• 

 Switch the appliance off when it is not in use.

Limit the operating time!

All stages of the operating cycle must be conside-

red (for example, times in which the electric tools 

are switched o

ff

  and times in which the tool is 

switched on but operates without load).

Caution!

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.   Lung damage if no suitable protective dust 

mask is used.

2.   Damage to hearing if no suitable ear protec-

tion is used.

3.   Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and 

maintained.

5.  Before starting the equipment

Before you connect the equipment to the mains 

supply make sure that the data on the rating plate 

are identical to the mains data.

Warning! 

Always pull the power plug before making 

adjustments to the equipment.

 Pull the power plug before doing any mainte-

nance or assembly work on the equipment.

• 

The equipment has to be set up where it can 

stand securely.

• 

Before starting work, firmly screw the grin-

ding/sanding machine to the workbench or 

equivalent using the 4 mounting holes (8) in 

the base plate (9).

• 

All covers and safety devices have to be pro-

perly fitted before the equipment is switched 

on.

• 

It must be possible for the grinding/sanding 

wheel to run freely.

• 

Check that the voltage on the rating plate is 

the same as your supply voltage before you 

connect the equipment to the power supply.

• 

 Fit the sealing plug (21) on the underside of 

the water container (10). This needs to be 

pressed in with a little force.

5.1  Assembling the spark de

fl

 ector / safety 

window (Fig. 3/4)

• 

Fasten the spark deflector (3) to the machine 

(Fig. 3).

• 

To do this, use the socket head screws (11), 

washers (12), spring washers (13) and nuts 

(14).

• 

Tighten the screw connection using a 4 mm 

hex key and an 8 mm wrench. Note! Not 

supplied.

• 

Fit the safety window (2) to the spark deflec-

tor (3) using a lock screw (15), a washer (12), 

a spring washer (13) and a locking button 

(16) (Fig. 4).

5.2  Adjusting the spark de

fl

 ector (Fig. 5)

• 

With the help of the slots in the spark deflec-

tor (3) you can adjust it in vertical direction.

• 

To do so, slacken the socket head screws 

(11) and push the spark deflector as close as 

possible to the grinding/sanding wheel (5).

• 

Warning! The distance between the grinding/

sanding wheel (5) and the spark deflector (3) 

must be set as small as possible and under 

no circumstances should it exceed 2 mm.

• 

Then secure the spark deflector (3) again.

• 

Warning! Adjust the spark deflector (3) peri-

odically to compensate for wear on the grin-

ding/sanding wheel (5).

5.3  Fitting the workpiece support (Fig. 6)

• 

Fit the workpiece support (7) to the machine.

• 

Warning! The angled face of the workpiece 

support must point away from the grinding/

sanding wheel (5)!

• 

To achieve this, use the lock screw (17), the 

washer (18), the spring washer (19) and the 

locking button (20).

5.4  Setting the workpiece support (Fig. 7)

• 

With the help of the slot in the workpiece 

support (7) you can adjust it in horizontal 

direction.

• 

To do so, slacken the locking button (20) and 

Anl_TC_WD_200_150_SPK9.indb   22

Anl_TC_WD_200_150_SPK9.indb   22

23.06.2020   15:30:18

23.06.2020   15:30:18