Korting KHT 6332 W - Инструкция по эксплуатации - Страница 19

through either a plug 

fused 3A

 or hardwired to a 2 fase spur 

protected by 

3A fuse.

2. Warning !
In certain circumstances electrical appliances may be a 
danger hazard. 
A) Do not check the status of the filters while the cooker 
hood is operating
B) Do not touch bulbs or adjacent areas, during or straight 
after prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker 
hood 
D) Avoid free flame, as it is damaging for the filters and 
a fire hazard
E )   Co n s t a n t l y   c h e c k   fo o d   f r y i n g   t o   avo i d   t h a t   t h e 
overheated oil may become a fire hazard
F )   D i s c o n n e c t   t h e   e l e c t r i c a l   p l u g   p r i o r   t o   a n y 
maintenance.
G) This appliance is not intended for use by young children 
or infirm persons without supervision
H) Young children should be supervised to ensure they do 
not play with the appliance
I) There shall be adequate ventilation of the room when 
the rangehood is used at the same time as appliances 
burning gas or other fuels
L) There is a risk of fire if cleaning is not carried out in 
accordance with the instructions

This appliance conforms to the European Directive EC/2002/96, 
Waste Electrical and Electronic Equipment ( WEEE). By making 
sure that this appliance is disposed of in a suitable manner, 
the user is helping to prevent potential damage to the 
environment or to public health.

The  

  symbol on the product or on the accompanying 

paperwork indicates that the appliance should not be treated 
as domestic waste, but should be delivered to a suitable 
electric and electronic appliance recycling collection point.  
Follow local guidelines when disposing of waste. For more 
information on the treatment, re-use and recycling of this 
product, please contact your local authority, domestic waste 
collection ser vice or the shop where the appliance was 
purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out by 
specialised personnel.  

• Electrical Connection

The appliance has been manufactured as a class II, therefore 
no earth cable is necessary. 
The connection to the mains is carried out as follows: 
BROWN = 

L

 line

BLUE = 

N

 neutral

If not provided, connect a plug for the electrical load indicated 
on the description label. Where a plug is provided, the 
cooker hood must be installed in order that the plug is easily 
accessible.  An omnipolar switch with a minimum opening of 
3mm between contacts, in line with the electrical load and 
local standards, must be placed between the appliance and 
the network in the case of direct connection to the electrical 
network. 

• 

 The minimum distance between the support surfaces of 

the cooking pots on the cooker top and the lowest part of 
the cooker hood must be at least 65 cm. 
If a connection tube composed of two parts is used, the 

upper part must be placed outside the lower part. Do not 
connect the cooker hood exhaust to the same conductor 
used to circulate hot air or for evacuating fumes from other 
appliances generated by other than an electrical source. In 
the case of assembly of the appliance in the suction version 
prepare the hole for evacuation of the air.

• 

 We recommend the use of an air exhaust tube which has 

the same diameter as the air exhaust outlet hole. If a pipe 
with a smaller diameter is used, the efficiency of the product 
may be reduced and its operation may become noisier.

• Warning: 

if the bulbs are not working, ensure that they are 

screwed in fully.

• 

 Installation

Prior to proceeding with the assembly operations (according 
to the model that you have purchased), to facilitate handling 
of the device, remove the grille as indicated in fi gure 7 or the 
aluminium panels as indicated in fi gure 8.
• The appliance is equipped with 2 air outlets, to be used in 
accordance with your specifi c requirements: one is located 
on the upper part of the appliance and the other at the rear 
(Fig. 1A). 
The fl ange 

D

, to which the air exhaust pipe is connected, 

and a plug 

B

, used to shut off  the unused air outlet, are both 

supplied with the product.

• This device may be installed in two diff erent ways:

1. Fixing the hood to the lower part of the wall cabinet 

(Fig.2)
- Make 4 holes in the wall cabinet respecting the measurements 
indicated in fi gures 2

 A

-2 

C

.

- Position the hood underneath the wall cabinet and fi x  it 
into place using 4 screws (not supplied) suitable for the type 
of cabinet.

2. Fixing the hood to the wall

 (Fig.2).

- Make 4 holes in the wall cabinet respecting the measure-
ments indicated in fi gures 2 

A

-2 

B

. - Hang the hood on the 

wall, using the 2 holes 

H

, align it in a horizontal position and 

fi x it defi nitively to the wall using the two lower safety holes 

I 

(Fig. 2B). For the various installations use screws and screw 

anchors suited to the type of wall (e.g. reinforced concrete, 
plasterboard, etc.). If the screws and screw anchors are provided 
with the product, check that they are suitable for the type of 
wall on which the hood is to be fi xed.

• Mounting decorative ducts (optional)

- This hood model may have decorative ducts as 

optional

accessories - ask your retailer for information.
- Provide the electrical power supply within the space of the 
decorative duct.  
- If your appliance must be installed as an extractor version or 
as a version with an external motor, make sure an air exhaust 
hole is prepared (fi g. 1A - 1C). 
- Adjust the width of the upper duct support bracket (Fig. 
3). Then fi x it to the wall so that it is on the same axis as the 
hood using screws 

A

 (Fig.3) and adhering to the distance from 

the ceiling shown in (Fig. 2 

B

). Connect the fl exible hose (not 

supplied) to the fl ange 

D

 (fi g. 1A).

- Put the upper connector 

F 

into the lower connector 

G

and hang the decorative ducts on the wall, as indicated in 
fi gure 4. 
- Connect the fl exible hose to the air exhaust hole made 
previously (only in the extraction or external motor version).
- Pull out the top connector 

F 

as far as the bracket and fi x it 

- 19 -