Falmec Exploit Top 90 - Инструкция по эксплуатации - Страница 18

18

MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching of the 
main switch.

Regular maintenance guarantees proper operation and good performance over time. 

Special attention is to be paid to the metal anti-grease ilters and active carbon ilters. In fact, frequent cleaning of the ilters and their supports 
ensures that no grease is accumulated on the hood, which is dangerous and can cause ires.

EXTERNAL CLEANING

You are advised to clean the external surfaces of the hood

 at least once every 15 days

 to prevent oily substances and grease from sticking to them.

Cleaning the hood, which is made of anti-ingerprint treated material (Fasteel), is to be carried out by only using water and neutral soap and a soft cloth.
Finish of cleaning by rinsing well and drying with soft cloths.

Do not use too much water next to the push button control panel and lighting devices in order to prevent humidity from reach-
ing electronic parts.
You must not use detergents containing abrasive, acid or corrosive substances or abrasive cloths: a direct consequence of not 

complying with these warnings will result in irreversible deterioration of the hood's surface.

The Manufacturer declines all responsibility for failure to comply with these instructions.

It is possible to remove the external suction panel completely in order to facilitate its cleaning (refer to the instructions 

G

 on page 

6

).

CLEANING OF INTERNAL PARTS

It is forbidden to clean electrical parts, or parts related to the motor inside the hood, with liquids or solvents.

Do not use abrasive products. All these operations are to be carried out after having disconnected the equipment from the 
electrical mains power supply.

METAL ANTI-GREASE FILTERS 

The metal anti-grease ilters are there to contain suspended grease particles: deposited on the ilters, these feed on any 

lames released when cooking, generate unpleasant odours, and compromise the passage of air, thus reducing suction 
performance of the hood. 
For this reason, it is advised to 

frequently

 wash the metal ilters (

at least

once a month) 

leaving them to soak in boiling 

water and dish washing liquid for 1 hour, taking care not to bend them. Do not use corrosive, acid or alkaline detergents. 
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the ilter material to darken: to reduce the possibility of this 
problem from happening, use low-temperature washes (55°C max.).

Open the external suction panel to remove the metal anti-grease ilters (refer to the instructions 

G

 on page 

6

), then operate the handle 

(refer to the instructions 

H

 on page 

6

).  Carry out operations in reverse order to insert them.

ACTIVE CARBON FILTERS

Active carbon ilters have the function of retaining odours in the air low passing through them. The air, puriied by running 
many times through the ilter, is recirculated into the kitchen. 
Active carbon ilters 

cannot be washed

 and are to be immediately replaced every 

3-4 months

 (depending on the fre-

quency of use of the hood).
Dispose of the active carbon ilters in compliance with the regulations in force in the country of use.

To replace the active carbon ilters, open the external suction panel (refer to the instructions 

G

 on page 

6

), remove the metal an-

ti-grease ilters (refer to the instructions 

H

 on page 

6

) and follow the instructions 

I

 on page 

6

. 

DISPOSAL AFTER END OF USEFUL LIFE

This symbol on products and/or in accompanying documents means that electrical and electronic products used must not be disposed of with general do-
mestic waste. For personal treatment, recovery and recycling, you are kindly asked to take these products to designated waste collection points where they 
will be accepted freely. Alternatively, in other countries, it is possible to take products back to the local dealer and purchase a new similar product. Proper 
disposal of these products contributes to saving valuable resources and avoid potential negative efects on personal health and the environment, which 
may be caused by inappropriate disposal of waste. You are kindly asked to contact your local authorities for further information regarding the designated 
waste collection points nearest to you. Penalties for improper disposal of such waste can be applied in compliance with national regulations.

INFORMATION REGARDING DISPOSAL IN EU COUNTRIES

The EU Directive with regard to WEEE has been implemented diferently by each nation, therefore, should you wish to dispose of this equipment, we advise 
you to contact the local authorities or the dealer to ask for the correct method of disposal.

INFORMATION REGARDING DISPOSAL IN OTHER NON-EU COUNTRIES. 

This symbol is only valid in the European Union: if you wish to dispose of this product in other countries, we advise you to contact your local authorities or 
dealer to ask for the proper method of disposal.