Elica FOLD GR/A/72 - Инструкция по эксплуатации - Страница 9

● 

 Duct-Out Version:

Vapours are evacuated outside through an exhaust pipe attached to the connecting flange.
CAUTION! If the product features one or more carbon filters, they must be removed.
Connect  the  product  to  wall-mounted  exhaust  pipes  and  holes  with  a  diameter  equivalent  to  the  air  outlet  (connecting
flange).
The use of pipes and outlet holes in the wall with a smaller diameter will reduce the extraction performance and drastically
increase the noise level.
All responsibility in this regard is therefore denied.
• Use a ducting pipe with the shortest length necessary.
• Use a ducting pipe with the least number of bends possible (maximum bend angle: 90°).
• Avoid drastic changes in the ducting pipe diameter.

● 

 Recirculating Version:

The suctioned air will be degreased and deodorised before it is sent back into the room. To use the product in this version,
it is necessary to install an additional activated carbon filter system.

ASSEMBLY BEFORE INSTALLATION

• Check that the product is the right size for the installation area.
• Remove the activated carbon filter(s) if supplied (see also relevant paragraph).
• It(they) must be reinstalled if the product is used in the filter version.
• If there are panels and/or walls and/or wall units on the sides, make sure that there is enough space to install the product
and that it is always possible to access the control panel easily.
• The product is equipped with fixing plugs suitable for most walls/ceilings. However, it is necessary to consult a qualified
technician to make sure that the materials are suitable for the type of wall/ceiling. The wall/ceiling must be strong enough
to support the weight of the hood.

 ELECTRICAL CONNECTION SAFETY

•The  mains  voltage  must  correspond  to  the  voltage  indicated  on  the  label  found  inside  the  product.  •If  it  features  a  plug,
connect the product to a socket that complies with current standards, located in an area accessible even after installation.
•If  it  does  not  feature  a  plug  (direct  connection  to  the  mains)  or  the  plug  is  not  located  in  an  accessible  area,  even  after
installation,  apply  a  standard  double  pole  switch  that  ensures  complete  disconnection  from  the  mains  in  category  III
overvoltage  conditions,  in  accordance  with  the  installation  rules.  •  Warning!  The  power  cable  must  be  replaced  by  the
authorised technical support service or by a person with similar qualifications.
●  Please  note!  Before  reconnecting  the  circuit  to  the  mains  power  supply,  make  sure  that  it  is  working  correctly,  always
check that the power cable is correctly installed.

 MAINTENANCE WARNINGS

•  Cleaning:  For  cleaning,  simply  use  a  cloth  moistened  with  neutral  liquid  detergents.  Do  not  use  cleaning  tools  or
instruments.
• Avoid the use of abrasive products. DO NOT USE ALCOHOL!

For product maintenance, see the images at the end of the installation marked by this symbol.

•

 Anti-Grease Filter: The metallic anti-grease filter must be cleaned once a month with non-aggressive detergen-

ts, manually or in a dishwasher on a short wash at low temperatures. To remove the anti-grease filter, pull the spring re-
lease handle.

•  The  Anti-Grease  Filter  traps  the  grease  particles  produced  during  cooking.  When  cleaned  in  the  dishwasher,  the  metal
grease filter may discolour, but its filtering characteristics remain unchanged.

•

 Carbon filter (for filter version only): The cartridge must be replaced at least every four months. It CANNOT

be washed or regenerated. As indicated in the drawings section: remove the anti-grease filters, apply a carbon filter on
each side and attach it to the product. Put the anti-grease filters back in place.

• The carbon filter retains any unpleasant odours produced during cooking. • The saturation of the carbon filter can occur

8