DeLonghi KCX-AF100X - Инструкция по эксплуатации - Страница 8

- 8 -

regularity of the maintenance operations, in par ticular, the
active carbon filter.

•  

T h e   a n t i - gr e a s e   f i l t e r s   c a p t u r e   t h e   g r e a s e   p a r t i c l e s

suspended in the air, and are therefore subject to clogging
according to the frequency of the use of the appliance.
In order to prevent fire hazard, it is recommendable to clean
the filter at a maximum of 2 months by carrying out the
following instr uctions:
- Remove the filters from the cooker hood and wash them in a
solution of water and neutral liquid detergent, leaving to soak.
- Rinse thoroughly with warm water and leave to dr y.
- The filters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several washes.
This is not cause for customer complaint nor replacement of
panels.

• 

The active carbon filters pur ify the air that is replaced in the

environment.  The filters are not washable nor re-useable and
m u s t   b e   r e p l a c e d   a t   m a x i mu m   eve r y   fo u r   m o n t h s. T h e
saturation of the active carbon filter depends on the frequency
of use of the appliance,   by the type of cooking and the
regularity of cleaning the anti-grease filters.

• 

 Clean the fan and other surfaces of the cooker hood regularly

using a cloth moistened with denatured alcohol or non abrasive
liquid detergent.
• The illumination installation is designed for use dur ing
cooking and not for prolonged general illumination of the
environment. Prolonged use of the illumination installation
notably reduces the duration of the bulb.

COMMANDS: 

(Fig.13)

Push-button A 

= on/off lights switch

Push-button B 

= on/off cooker hood switch.  The appliance

switches on at speed level 1,  If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood.  If the
cooker hood is at speed level 1 it will not be necessary to
depress the push-button to switch the cooker hood off.
Decreases the motor speed.

Display C 

= indicates the motor speed level selected and

activates the timer.

Push-button D 

= switches on the cooker hood.  Increases

the motor speed.  Touching the key at 3rd speed, the inten-
sive function runs for 10', then the appliance go back to work
at the original speed. During this function the display blinks.

Key E 

= The Timer times the functions on activation for 15

minutes, after which they are switched off. The Timer is
deactivated by re-pressing 

Key E

. When the Timer is acti-

vated the decimal point must flash on the display. The Timer
cannot be activated if the intensive speed is functioning.

The 

“clean air” 

function is activated by pressing key 

E

 for 2

seconds when the appliance is switched off. This switches
the motor on for 10 minutes every hour at the first speed.
During functioning a rotar y movement of the per ipheral seg-
ments must be visualised on the display. When this time has
passed the motor switches off and the fixed letter 

“C”

 must

be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on. Press any key apar t
from the light keys to return to normal functioning. Press key

E

 to deactivate the function.

• Active carbon/grease filter saturation 

fig.13

 :

- When display item 

C

 flashes, at a speed where it alternates

with the letter 

F 

(e.g. 1 and 

F

), the 

grease 

filters must be

washed.
- When display item 

C

 flashes, at a speed where it alternates

with the letter 

A 

(e.g. 1 and 

A

), the 

carbon 

filters must be

replaced.
A f t e r   t h e   c l e a n   f i l t e r   h a s   b e e n   p o s i t i o n e d   c o r r e c t l y,   t h e
electronic memor y must be reset by pressing button 

A

 for

approximately 

5 seconds

, until the indication 

F

 or 

A

 shown

on the display 

C

 stops flashing.

• COMMANDS: ELECTRONIC 

(Fig.12 A):

A

 = LIGHT

B

 = OFF/SPEED I

C

 = SPEED II

D

 = SPEED III

E

 = AUTOMATIC STOP TIMER – 15 minutes 

(*)

F

 = FILTER SATURATION RESET LIGHT

When the “filter saturation” light flashes, the anti-grease filters
must be washed. When the light comes on without flashing,
the anti-grease filters must be washed and the carbon filters
replaced (in case of operation whit the recycling version).

When this operation has been completed, press the key to
reset it.

• COMMANDS:

(Fig.11A) 

LUMINOUS 

-  (Fig.12B)

 ELECTRONIC 

the key

symbols are explained below:

A

 = LIGHT

B

 = OFF

C

 = SPEED I

D 

= SPEED II

E

 = SPEED III

F 

= AUTOMATIC STOP TIMER - 15 minutes 

(*)

• 

If your appliance does not have the 

INTENSIVE

 speed

function, press key E for two seconds and it will be activated
for 10 minutes after which it will retur n to the previously set
speed. When the function is active the LED flashes. To interrupt
it before the 10 minutes have expired press key 

E 

again.

•

 By pressing key 

F 

for two seconds (with the hood switched

off) the “

clean air

” function is activated. This function switches

the appliance on for ten minutes ever y hour at the first speed.
As soon as this function is activated the motor star ts up at the
first speed for ten minutes, During this time key 

F 

and key 

C

must flash at the same time.
After ten minutes the motor switches off and the LED of key 

F

remains switched on with a fixed light until the motor starts up
again at the first speed after fifty minutes and keys 

F 

and 

C

start to flash again for ten minutes and so on.
By pressing any key for the exclusion of the hood light the
hood will return immediately to its normal functioning (e.g. if
key D is pressed the “

clean air

” function is deactivated and

the motor moves to the 2nd speed straight away. By pressing
key 

B 

the function is deactivated).

(*)

 The 

“automatic stop timer” 

delays stopping of the hood,

which will continue functioning for 15 minutes at the operat-
ing speed set at the time this function is activated.

• Active carbon/grease filter saturation:

- When  button 

A

 flashes at a frequency of 

2 seconds

, the

grease

 filters must be cleaned.

- When button 

A

 flashes at a frequency of 

0.5 seconds

, the

carbon

 filters must be replaced.

After the clean filter has been replaced, the electronic memory
must be reset by pressing button 

A

 for approximately 

5

seconds

, until the light on the button stops flashing.

•COMMANDS: 

(Fig.11B)

 MECHANICAL

_the key symbols are

explained below:

A

 = LIGHT

B

 = OFF

C

 = SPEED I

D 

= SPEED II

E

 = SPEED III

G 

= MOTOR  WORKING indicator

THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.