Vestel VH64E352B - Инструкция по эксплуатации - Страница 32

EN - 12

4. USE OF PRODUCT

4.1 hob ControlS

The appliance is operated by pressing 

buttons and the functions are confirmed by 

displays and audible sounds.

1

2 3 4

5

6 7

8

9

10

11

12 13 14

15

1-

Heater display

2-

Activate/Deactivate heater

3-

Activate/Deactivate timer

4-

Timer display

5-

Timer function cooking zone indicators

6-

Triple zone indicator

7-

Dual zone indicator

8-

Stop/Go

9-

Dual/Triple zone selection

10-

Decimal point

11-

Heat setting/Timer sliding button

12-

Heat setting/Timer sliding indicator

13-

Key lock indicator

14-

Key lock

15-

On/Off

Mode Descriptions

Stand-By-

Mode

S-Mode

The mains is applied to the 

hob control and all heater 

displays are off or a residual 

heat display is active.

Operating-

Mode

B-Mode

At least one heater display 

shows a heat setting 

between “

0

” and “

9

”.

Lock Mode

VR-

Mode

The hob control is locked.

Switching the Appliance On and Off

If the appliance is in Stand-By mode, it 

is put in Operating mode by pressing the 

On/Off button   for at least 1 second. A 

buzzer will sound to indicate the successful 

operation.

A “

0

” will appear on all heater displays and 

all decimal points for the heaters will flash 

(1 second on, 1 second off).

If there is no operation within 10 seconds, 

the display for all heaters will switch off.

If the displays switch off, the heater will be 

sent into Stand-By mode.

If   is pressed for more than 2 seconds 

(in Operating-Mode), the appliance will 

switch off and will enter S-Mode again. The 

appliance can be switched off by pressing 

 at any time; even if other buttons are 

pressed simultaneously.

If there is any residual heat from a heater, 

this will be indicated in the corresponding 

Heater Display by a “

H

”.

Selecting a Heater

If a single heater is chosen with the 

corresponding Activate/Deactivate Heater 

Button   , the Decimal Point of the Heater 

Display will flash. For the selected heater, 

the heat level can be set between 1 and 9 

by touching the Heat Setting Slider Button 

 .

The slider button must be pressed within 3 

seconds of selecting a heater, otherwise the 

heater selection will be cleared and the heat 

setting Decimal Point will disappear. If there 

is no further operation within 10 seconds, 

the heater will return to S-Mode.

The heat setting can always be changed by 

pressing 

 to set a level 

between 1 and 9.

Each slider button operation or each display 

change will be accompanied by a buzzer 

sound.

Switching On the Dual and Triple Zones

Switching on the Dual Zone

The Dual Zone can be activated by 

pressing  , after a heater and its 

corresponding desired heat level (between 

1 and 9) has been selected. A buzzer will 

sound to confirm this operation. At the same 

time, the corresponding Dual Zone Indicator 

will illuminate. To deactivate the Dual Zone, 

press   again.

Switching on the Triple Zone

Similar to activating the Dual Zone, a triple 

zone can only be switched on if the basic 

zone of a heater has been selected and its 

corresponding heat level, between 1 and 9, 

has been set. This will be indicated by the 

illumination of the heater's corresponding 

decimal point.

If   is pressed, the signal will sound and 

the Dual Zone Indicator will illuminate. If 

is pressed a second time, another buzzer 

will sound to indicate the activation of the