Philips GC7619/20 - Инструкция по эксплуатации - Страница 27

27

Problem

Possible cause

Solution

EN

The appliance does not produce 

any steam.

There is not enough water in the 

water tank.

Fill the water tank beyond the MIN indication. 

Press and hold the steam trigger until steam 

comes out. It may take up to 30 seconds until 

steam comes out.

You have not pressed the steam 

trigger.

Press the steam trigger and keep it pressed when 

you iron.

You have just installed a new 

ANTI-CALC car tridge.

Press and hold the steam trigger for 10 seconds 

until steam comes out.

The ANTI-CALC car tridge is not 

placed properly.

Press down the ANTI-CALC car tridge until it 

locks into position.

The appliance beeps and less or 

no steam comes out of the iron 

when I press the steam trigger.

You have to replace the ANTI-

CALC car tridge.

Replace the ANTI-CALC car tridge (see 

ANTI

CALC

). 

You can also use demineralised water or descaled 

water from the IronCare. In that case, you need to 

leave the exhausted car tridge in the compar tment.

The ‘ANTI-CALC  car tridge 

replacement’ light keeps flashing.

You have to replace the ANTI-

CALC car tridge.

Replace the ANTI-CALC car tridge (see 

ANTI

CALC

). 

You can also use demineralised water or descaled 

water from the IronCare. In that case, you need to 

leave the exhausted car tridge in the compar tment.

The appliance produces a loud 

pumping sound (subtle pumping 

sound is normal).

You have just installed a new 

ANTI-CALC car tridge.

Continue to press the steam trigger until the 

pumping sound stops and steam comes out of 

the soleplate.

The water tank is empty.

Refill the water tank with water and press the 

steam trigger until the pumping sound stops and 

steam comes out of the soleplate.

The ANTI-CALC car tridge is not 

in place.

Place the ANTI-CALC car tridge (see 

).

The ANTI-CALC car tridge is 

damaged or shows cracks or 

hairline cracks.

Inspect the ANTI-CALC car tridge thoroughly. If 

you see any sign of damage or cracks, no matter 

how small, replace the ANTI-CALC car tridge 

with a new one.

The appliance has switched off.

The safety auto-off function is 

activated automatically when the 

steam generator has not been 

used for more than 5 minutes.

Press the on/off button to reactivate the steam 

generator.

The iron leaves a shine or an 

imprint on the garment.

The surface to be ironed was 

uneven, for instance because you 

were ironing over a seam or a 

fold in the garment.

Perfect Care is safe on all garments. The shine 

or imprint is not permanent and will disappear 

when you wash the garment. Avoid ironing over 

seams or folds or you can place a cotton cloth 

over the area to be ironed to avoid imprints.

The ironing board cover 

becomes wet or water droplets 

come out of the soleplate.

Steam has condensed on the 

ironing board cover after a long 

ironing session.

Replace the ironing board cover if the foam 

material has worn out. You can also add an extra 

layer of felt material under the ironing board cover 

to prevent condensation on the ironing board.

You may have an ironing board 

that is not designed to cope with 

the high steam rate of the steam 

generator.

Put an extra layer of felt material under the 

ironing board cover to prevent condensation on 

the ironing board.

There is too much steam 

coming out of the iron.

The default setting of the iron is 

the OptimalTemp setting. In this 

setting the iron provides a high 

steam output.

Activate the ECO mode to iron with a lower 

steam output. See 

.

4239_000_9429_1_Picture Rich_A5_v1.indd   27

8/12/14   10:49 AM