Makita DUR192LZ - Инструкция по эксплуатации - Страница 12

12 ENGLISH

Putting into operation

1. 

Before assembling or adjusting the tool, 

remove the battery cartridge.

2. 

Before installing the battery cartridge, inspect 

the tool for damages, loose screws/nuts or 

improper assembly. If the cutting tool is bent 

or damaged, replace it. Check all control levers 

and switches for easy action. Clean and dry 

the handles.

3. 

Never attempt to switch on the tool if it is dam-

aged or not fully assembled.

 Otherwise serious 

injury may result.

4. 

Adjust the shoulder harness and hand grip to 

suit the operator's body size if adjustable. 

5. 

When inserting a battery cartridge, keep the 

cutting attachment clear of your body and 

other object, including the ground.

 It may rotate 

when starting and may cause injury or damage to 

the tool and/or property.

6. 

Remove any adjusting key, wrench before 

turning the tool on.

 An accessory left attached 

to a rotating part of the tool may result in personal 

injury.

7. 

The cutting tool has to be equipped with the 

guard. Never run the tool with damaged guards 

or without guards in place!

8. 

Make sure there are no electrical cables, water 

pipes, gas pipes etc. that could cause a hazard 

if damaged by use of the tool.

9. 

The condition of the cutting tool, protective 

devices and shoulder strap must be checked 

before commencing work.

Operation

1. 

In the event of an emergency, switch off the 

tool immediately.

2. 

If you feel any unusual condition (e.g. noise, 

vibration) during operation, switch off the 

tool and remove the battery cartridge. Do not 

use the tool until the cause is recognized and 

solved.

3. 

The cutting attachment continues to rotate for 

a short period after turning the tool off. Don't 

rush to contact the cutting attachment.

4. 

During operation, use the shoulder harness if 

supplied with the tool. Keep the tool on your 

right side firmly.

5. 

Do not overreach. Keep proper footing and 

balance at all times. Watch for hidden obsta-

cles such as tree stumps, roots and ditches to 

avoid stumbling.

6. 

Always be sure of your footing on slopes.

7. 

Walk, never run.

8. 

Never work on a ladder or tree to avoid loss of 

control.

9. 

If the tool gets heavy impact or fall, check the 

condition before continuing work. Check the 

controls and safety devices for malfunction. If 

there is any damage or doubt, ask our authorized 

service center for the inspection and repair.

10. 

Take a rest to prevent loss of control caused 

by fatigue.

 We recommend taking a 10 to 20-min-

ute rest every hour.

11. 

When you leave the tool, even if it is a short 

time, always remove the battery cartridge.

 The 

unattended tool with the battery cartridge installed 

may be used by unauthorized person and cause 

serious accident.

12. 

If grass or branches get caught between the 

cutting attachment and guard, always turn 

the tool off and remove the battery cartridge 

before cleaning. 

Otherwise the cutting attach-

ment may rotate unintentionally and cause serious 

injury.

13. 

Never touch moving hazardous parts before 

the moving hazardous parts have come to 

a complete stop and the battery cartridge is 

removed.

14. 

If the cutting attachment hits stones or other 

hard objects, immediately turn the tool off. 

Then remove the battery cartridge and inspect 

the cutting attachment.

15. 

Check the cutting attachment frequently 

during operation for cracks or damages. 

Before the inspection, remove the battery 

cartridge and wait until the cutting attachment 

stops completely. Replace damaged cutting 

attachment immediately, even if it has only 

superficial cracks.

16. 

Never cut above waist height.

17. 

Before starting the cutting operation, wait until 

the cutting attachment reaches a constant 

speed after turning the tool on.

18. 

When using a cutting tool, swing the tool 

evenly in half-circle from right to left, like 

using a scythe.

19. 

Hold the tool by insulated gripping surfaces 

only, because the cutting tool may contact 

hidden wiring.

 Cutting tool contacting a "live" wire 

may make exposed metal parts of the tool "live" 

and could give the operator an electric shock.

20. 

Do not start the tool when the cutting tool is 

tangled with cut grass.

21. 

Before starting the tool, be sure that the cut-

ting tool is not touching the ground and other 

obstacles such as a tree.

22. 

During operation always hold the tool with 

both hands. Never hold the tool with one hand 

during use.

23. 

Do not operate the tool in bad weather or if 

there is a risk of lightning.

24. 

Operate the tool only if you are in good phys-

ical condition. Perform all work calmly and 

carefully. Use common sense and keep in mind 

that the operator or user is responsible for 

accidents or hazards occurring to other people 

or their property.

25. 

Except in case of emergency, never drop 

or cast the tool to the ground or this may 

severely damage the tool.

26. 

Never drag the tool on the ground when mov-

ing from place to place, the tool may become 

damaged if moved in this manner.

27. 

Don't force the tool. It will do the job better and 

with less likelihood of a risk of injury at the 

rate for which it was designed.