Greenworks GD40BCB 40 В, с АКБ 4 А*ч и ЗУ 2105707UB - Инструкция по эксплуатации - Страница 5

English (original instructions)

EN

DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET

Only the parts shown on the parts list are intended to be re-

paired or replaced by the customer. All other parts should 

be replaced at an Authorised Service Centre.

WARNING

To avoid serious personal injury, always remove the bat-

tery pack from the tool when cleaning or performing any 

maintenance.

SPOOL REPLACEMENT  

See Figure 9.

Use  original  manufacturer’s  replacement  cutting  line  for 

best performance.

„

Remove the battery pack.

„

Push in tabs on side of spool cover.

„

Pull spool cover up to remove.

„

Remove the old spool.

„

To install the new spool, make sure the cutting line is 

captured in the slot on the new spool. Make sure the 

end of the cutting line is extended approximately 15cm 

beyond the slot.

„

Install the new spool so that the cutting line and slot 

align with the eyelet in the cutting head. Thread the 

cutting line into the eyelet.

„

Pull the cutting line extending from the cutting head so 

the cutting line releases from the slot in the spool.

„

Reinstall the spool cover by depressing tabs into slots 

and pushing down until spool cover clicks into place.

CUTTING LINE REPLACEMENT  

See Figures 10.

„

Remove the battery pack.

„

Remove the spool from the cutting head. 

NOTE: Remove any old cutting line remaining on the 

spool.

„

Cut a piece of cutting line approximately 3m long.

„

Bend the line at the midpoint and hook the loop into the 

slot  in  the  center  rim  of  the  spool.  Ensure  line  snaps 

into position in the slot.

„

Wind the line evenly and firmly in a clockwise direction. 

Once completed, put the line in the slot so it does not 

unwind.

„

Do not wind the line beyond the edge of the spool.

ASSEMBLY THE BRUSH CUTTER  

See Figure 11.

Warning: Be careful of sharp edges and to wear gloves.

„

Remove the battery pack.

„

Ensure the 'F’ is installed on the shaft of the trimmer.

„

Insert a suitable screw driver through the two holes.

„

Place the Brush-cutter Blade 'G' on top of the spacer 'F' 

ensuring it is centered.

„

Place washer 'H on top of the Brush-cutter Blade 'G'

„

Place cover 'I' over washer 'H'

„

Using a 19mm or 3/4" wrench tighten the lock-nut 'J' 

Counter-clockwise  to  44-58"  N.M  or  32-42  ft/lbs  of 

torque.

„

Spin the Brush-cutter Blade 'B' to ensure Brushcutter 

Blade is secured tightly.

STORING THE TRIMMER

„

Remove  the  battery  pack  from  the  trimmer  before 

storing.

„

Store it in a place that is inaccessible to children.

„

Keep  away  from  corrosive  agents  such  as  garden 

chemicals and de-icing salts.

„

Store and charge your batteries in a cool area. 

Temperatures above or below normal room 

temperature will shorten battery pack life.

„

Store the battery pack where the temperature is below 

27˚C and away from moisture.

„

All batteries gradually lose their charge. The higher the 

temperature, the quicker they lose their charge. If you 

store  your  unit  for  long  periods  of  time  without  using 

it, recharge the batteries every month or two. This 

practice will prolong battery pack life.

„

Secure the trimmer during transport to prevent damage 

or  injury.  Clean  and  maintenance  before  storage,  use 

of  guards  on  cutting  attachments  with  metal  blades. 

Use  of  cover  for  metal  blades  during  transport  and 

storage.

ENVIRONMENTAL PROTECTION

„

Environmental  protection  should  be  a  priority  of 

considerable importance when using the machine, 

for  the  benefit  of  both  social  coexistence  and  the 

environment in which we live. Try not to cause any 

disturbance to the surrounding area.

„

Scrupulously  comply  with  local  regulations  for  the 

disposal  of  packaging,  deteriorated  parts  or  any 

elements with a strong environmental impact; this 

waste must not be disposed of as normal waste, it must 

be  separated  and  taken  to  specified  waste  disposal 

centres where the material will be recycled.

„

Scrupulously  comply  with  local  regulations  for  the 

disposal of waste materials after mowing.

„

At  the  time  of  decommissioning,  do  not  pollute  the 

environment with the machine, but hand it over to a 

disposal centre, in accordance with the local laws in 

force.

4