FERM GTM1005 - Инструкция по эксплуатации - Страница 7

7

EN

for carrying, pulling or unplugging the 
power tool. Keep cord away from heat, oil, 
sharp edges or moving parts. 

Damaged or 

entangled cords increase the risk of electric 
shock.

e)  

When operating a power tool outdoors, use 
an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces 
the risk of electric shock.

f) 

 If operating a power tool in a damp location 
is unavoidable, use a residual current 
device (RCD) protected supply.

 Use of an 

RCD reduces the risk of electric shock.

3)  Personal safety

a)  

Stay alert, watch what you are doing and 
use common sense when operating a 
power tool. Do not use a power tool while 
you are tired or under the influence of 
drugs, alcohol or medication. 

A moment of 

inattention while operating power tools may 
result in serious personal injury.

b) 

 Use personal protective equipment. Always 
wear eye protection.

 Protective equipment 

such as dust mask, non-skid safety shoes, hard 
hat, or hearing protection used for appropriate 
conditions will reduce personal injuries.

c)   

Prevent unintentional starting. Ensure the 
switch is in the off-position before connecting 
to power source and/or battery pack, picking 
up or carrying the tool. 

Carrying power tools 

with your finger on the switch or energising power 
tools that have the switch on invites accidents.

d) 

 Remove any adjusting key or wrench before 
turning the power tool on. 

A wrench or a key 

left attached to a rotating part of the power 
tool may result in personal injury.

e)  

Do not overreach. Keep proper footing 
and balance at all times. 

This enables better 

control of the power tool in unexpected 
situations.

f)  

Dress properly. Do not wear loose clothing 
or jewellery. Keep your hair, clothing and 
gloves away from moving parts. 

Loose 

clothes, jewellery or long hair can be caught in 
moving parts.

g) 

 If devices are provided for the connection 
of dust extraction and collection facilities, 
ensure these are connected and properly 
used.

 Use of dust collection can reduce dust 

related hazards.

h)  

Do not let familiarity gained from frequent use 
of tools allow you to become complacent and 
ignore tool safety principles.

 A careless action 

can cause severe injury within a fraction of a 
second.

4)   Power tool use and care

a) 

 Do not force the power tool. Use the correct 
power tool for your application.

 The correct 

power tool will do the job better and safer at 
the rate for which it was designed.

b) 

 Do not use the power tool if the switch 
does not turn it on and off. 

Any power tool 

that cannot be controlled with the switch is 
dangerous and must be repaired.

c)

Disconnect the plug from the power source 
and/or the battery pack from the power tool 
before making any adjustments, changing 
accessories, or storing power tools. 

Such 

preventive safety measures reduce the risk of 
starting the power tool accidentally.

d) 

 Store idle power tools out of the reach 
of children and do not allow persons 
unfamiliar with the power tool or these 
instructions to operate the power tool. 

Power tools are dangerous in the hands of 
untrained users.

e) 

 Maintain power tools. Check for 
misalignment or binding of moving parts, 
breakage of parts and any other condition 
that may affect the power tool’s operation. 
If damaged, have the power tool repaired 
before use. 

Many accidents are caused by 

poorly maintained power tools.

f) 

 Keep cutting tools sharp and clean. 

Properly 

maintained cutting tools with sharp cutting edges 
are less likely to bind and are easier to control.

g) 

 Use the power tool, accessories and 
tool bits etc. in accordance with these 
instructions, taking into account the 
working conditions and the work to 
be performed. 

Use of the power tool for 

operations different from those intended could 
result in a hazardous situation.

h) 

 Keep handles and grasping surfaces dry, clean 
and free from oil and grease.

 Slippery handles and 

grasping surfaces do not allow for safe handling 
and control of the tool in unexpected situations.