Oursson JM6001/GA - Инструкция по эксплуатации - Страница 18

18

ClEaNiNg aND maiNTENaNCE,

 F

ig. Е

1. 

Turn off the device before unplugging it.

2. Remove the pusher.
3. 

Remove the cup’s lid, Pic. E-1

1-Cup’s lid

2-Juice cup

NOTE: 

If the lid is locked and does not open, press 

REV, OFF and then ON. Repeat this process 2-3 

times. Then open the lid, slightly press on the lid 

and turn it counter-clockwise.

4. 

Carefully remove the cup from the device, Pic. 

E-2.

Remove all pulp from the juice-making cup. 

For an easier cleaning of the device, pour 

water into the feeding chute and turn on the 

juice maker for 30 seconds. 

After each use, immediately clean and wash 

your juice maker. If the remaining juice or 

pulp dries in the device, this will complicate 

disassembly and cleaning of the device. Also 

it may damage the device.

It is strictly forbidden to clean parts of the 

device in dishwasher or dry them in dryer, as 

this may damage the device.

5. Remove all the parts of the cup, Pic. E-3.
6. 

Flip the cup and place it under running water. 
Remove the silicon gasket to clean the pulp 

spout, Pic. E-4-1.

7. Rotating brush has silicone inserts. They are 

removable. If necessary, they can be removed 

and washed. After cleaning, install the inserts 

back into the recess. To do this, first insert the 

lower part into the slot facing down, and then 

straighten, Pic. E-5.

8. Wash all the elements of device, except of 

motor unit, in warm soapy water, using a 

brush. Wipe the motor unit with a soft damp 

cloth. Never immerse the motor unit in water 

because of the risk of electric shock.

9. 

After cleaning, thoroughly dry all the elements of 

the device and store them in a dry, clean place. 

POSSiblE PROblEmS aND SOlUTiONS 

Problem

Solutions

Device does 
not work on

•  Check whether the power cord is connected to the outlet. If the device is not connected, 

plug it to the outlet.

•  Check whether the device is assembled correctly. If not, disassemble and reassemble ac

-

cording to the instructions.

•  If the problem persists, contact an authorized service center OURSSON.

Little juice

•  The various ingredients have different moisture contents.

•  If the products are not fresh, they lost their juiciness. Put the ingredients in water for 1-2 

hours to recover.

•  Make sure that the silicone gasket is installed correctly and firmly.

•  If you are using ingredients with small seeds, then after few loads their presence can re

-

duce the amount of juice. For best results, between preparations disassemble the machine 

and clean it from seeds.

A lot of pulp in 
the juice

•  With continued juicing and depending on the ingredients, juice may contain much pulp.

•  To reduce the pulp in the juice, disassemble the juice cup and remove the pulp more often.

•  If the filter or screw is damaged - it can affect the performance and quality of juice. It is 

recommended to replace them. The service life of each part depends upon the duration 

and the method of using the device, and pressing ingredients.

•  If too much of the ingredients are loaded into the juice maker simultaneously, this can lead 

to frequent stoppages and to a large number of pulp in the juice. Place ingredients slowly 

and in small portions.

Extraneous 
sounds when 
the device is 
working

•  Make sure that all parts are correctly assembled. Try to disassemble and assemble the 

juice maker again and listen to the noise.

•  Do not turn the juice maker without ingredients or at least liquid in it. Empty working juice 

maker may damage the pressure screw.

• 

Check the size of the juicing products. It is recommended to cut large ingredients into small 

pieces 2×2×2 cm.

•  Depending on the type or size of various ingredients different noises my occur.

•  Noise may occur when the juice maker is working on uneven or inclined surfaces. Lace it 

on a flat stable surface.