Stanley SCH12S2 - Инструкция по эксплуатации - Страница 11

11

ENGLISH  

(Original instructions)

ENGLISH  

(Original instructions)

Never let any liquid get inside the tool; never immerse any part 

of the tool into a liquid. 

Charger Cleaning Instructions

WARNING:

 Shock hazard. Disconnect the charger from 

the AC outlet before cleaning. Dirt and grease may be 

removed from the exterior of the charger using a cloth 

or soft non-metallic brush. Do not use water or any cleaning 

solutions.

Optional Accessories

Warning!

 Since accessories, other than those offered by 

STANLEY have not been tested with this product, use 

of such accessories with this tool could be hazardous. 

To  reduce  the  risk  of  injury,  only  STANLEY  recommended 

accessories should be used with this product.
Consult your dealer for further information on the appropriate 

accessories.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be disposed of 

with normal household waste. 

Should you find one day that your STANLEY product needs 

replacement, or if it is of no further use to you, do not dispose of 

it with household waste. Make this product available for separate 

collection. 

Separate collection of used products and packaging 

allows materials to be recycled and used again. Re-use of 

recycled materials helps prevent environmental pollution 

and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical 

products from the household, at municipal waste sites or by the 

retailer when you purchase a new product.

BATTERIES

This long life battery pack must be recharged when it fails 

to produce sufficient power on jobs which were easily done 

before. At the end of its technical life, discard it with due 

care for our environment:

Run the battery down completely, then remove it from the tool. 
• Li-Ion cells are recyclable. Take them to your dealer or a local 

recycling station. The collected battery packs will be recycled or 

disposed of properly.

REMARKS

Stanley's policy is one of continuous improvement to our products 

and as such, we reserve the right to modify product specifications 

without prior notice.
• Standard equipment and accessories may vary by country.
• Product specifications may differ by country.
• Complete product range may not be available in all countries. 

Contact your local Stanley dealers for range availability.

LEVEL OF SOUND PRESSURE ACCORDING TO EN 60745:

Sound pressure (LpA) 65.0 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 76 dB(A), uncertainty (K) 3 dB(A)

VIBRATION  TOTAL  VALUES  (TRIAX  VECTOR  SUM) 

ACCORDING TO EN 60745:

Drilling into metal (ah, D) 0.9 m/s2, uncertainty (K) 1.5 m/s2
No load (ah, S) 1.1 m/s2, uncertainty (K) 1.5 m/s2

VIBRATION

The declared vibration emission values stated in the technical 

data and the declaration of conformity have been measured 

in accordance with a standard test method provided by EN 

60745 and may be used for comparing one tool with another. 

The declared vibration emission value may also be used in a 

preliminary assessment of exposure.

WARNING! 

The vibration emission value during actual use of the 

power tool can differ from the declared value depending on the 

ways in which the tool is used. The vibration level may increase 

above the level stated.
When vibration exposure to determine assessing safety measures 

required by 2002/44/EC to protect persons regularly using power 

tools in employment, an estimation of vibration exposure should 

consider, the actual conditions of use and the way the tool is 

used, including taking account of all parts of the operating cycle 

such as the times when the tool is switched off and when it is 

running idle in addition to the trigger time.

                                                SCH12

Technical data

Voltage                                 V

DC

                              10.8              

No-load speed:  

  1st gear                            min

-1

                        0–400    

  2nd gear                           min

-1 

                       0–1500     

Max torque                             Nm                              28      
Chuck capacity                       mm                             10
Maximum drilling capacity:  
Wood                                     mm    

         20  

Metal                                      mm    

        10 

Masonry                                  mm    

        8

Charger                                                            SC121

Input Voltage                         V

AC

                           220-240    

Output Voltage                       V

DC

                                22            

Output Current(DC)                 A                                1.25 
Approx. charge time                min                     70 (1,5 Ah) 

Battery                                                                 SB12S

Voltage                                  V

DC

                             10.8          

Capacity                                 Ah                               1.5          
Type                                                                       Li-Ion