RYOBI RDD18X-0 (5133004985) - Инструкция по эксплуатации - Страница 3

ENGLISH

EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL

3

Original Instructions

Safety, performance, and dependability have been given 
top priority in the design of your drill driver.

INTENDED USE

The drill driver is intended to be used only by adults who 
have read and understood the instructions and warnings 
in this manual, and can be considered responsible for their 
actions.
The product is intended for drilling into various materials, 
including wood, metal, and plastics using a drill bit having 
a shank diameter of less than 13 mm. The product can 
be used to drive and remove screws and bolts using an 
appropriate bit.
The product is intended for consumer use only. 
Do not use the product for any other purpose. Use of the 

SURGXFW IRU RSHUDWLRQV GLႇHUHQW IURP LQWHQGHG FRXOG UHVXOW

in a hazardous situation.

WARNING!

Read all safety warnings, instructions, 

illustrations and specifications provided with this 
power tool.

 Failure to follow all instructions listed below 

PD\UHVXOWLQHOHFWULFVKRFN¿UHDQGRUVHULRXVLQMXU\

Save all warnings and instructions for future reference.

DRILL DRIVER SAFETY WARNINGS

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

Ŷ

Use the auxiliary handle(s).

 Loss of control can cause 

SHUVRQDOLQMXU\

Ŷ

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the cutting 
accessory or fasteners may contact hidden wiring. 

Cutting accessory or fasteners contacting a “live” wire 
may make exposed metal parts of the power tool “live” 
and could give the operator an electric shock.

SAFETY INSTRUCTIONS WHEN USING LONG DRILL 
BITS

Ŷ

Never operate at higher speed than the maximum 
speed rating of the drill bit.

 At higher speeds, the 

bit is likely to bend if allowed to rotate freely without 

FRQWDFWLQJWKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\

Ŷ

Always start drilling at low speed and with the bit 
tip in contact with the workpiece.

 At higher speeds, 

the bit is likely to bend if allowed to rotate freely without 

FRQWDFWLQJWKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\

Ŷ

Apply pressure only in direct line with the bit and do 
not apply excessive pressure.

 Bits can bend causing 

EUHDNDJHRUORVVRIFRQWUROUHVXOWLQJLQSHUVRQDOLQMXU\

ADDITIONAL SAFETY WARNINGS

Ŷ

Clamp workpiece with a clamping device.

8QFODPSHG ZRUNSLHFHV FDQ FDXVH VHYHUH LQMXU\ DQG

damage.

Ŷ

Dust created by operating the product can cause 

UHVSLUDWRU\ LQMXU\ :HDU DSSURSULDWH GXVW FRQWURO PDVN

with filters suitable for protecting against particles from 
the material being worked on.

Ŷ

,QMXULHV PD\ EH FDXVHG RU DJJUDYDWHG E\ SURORQJHG
XVH RI D WRRO :KHQ XVLQJ DQ\ WRRO IRU SURORQJHG

periods, ensure you take regular breaks.

Ŷ

Switch off the product immediately if the bit stalls. Do 
not switch on the product again while the bit is stalled, 

as doing so could trigger a sudden recoil with a high 
reactive force. Determine why the bit stalled and rectify 
this, paying heed to the safety instructions.
The possible causes may be:

–

it is tilted in the workpiece

–

it has pierced the workpiece

–

the product is overloaded

Ŷ

Ambient temperature range for tool during operation is 
between 0°C and 40°C.

Ŷ

Ambient temperature range for tool storage is between 
0°C and 40°C.

Ŷ

The recommended ambient temperature range for the 
charging system during charging is between 10°C and 
38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

Ŷ

7R UHGXFH WKH ULVN RI ILUH SHUVRQDO LQMXU\ DQG SURGXFW

damage due to a short circuit, never immerse your 
tool, battery pack or charger in fluid or allow a fluid to 
flow inside them. Corrosive or conductive fluids, such 
as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

Ŷ

Ambient temperature range for battery during use is 
between 0°C and 40°C.

Ŷ

Ambient temperature range for battery storage is 
between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

KNOW YOUR PRODUCT

See page 56.

1. Gear selector
2. 

7RUTXHDGMXVWPHQWULQJ

3. Keyless chuck
4.  Direction of rotation selector
5.  Variable speed switch trigger
6.  Handle, insulated gripping surface
7. LED light
8. Battery port
9.  Auxiliary handle, insulated gripping surface
10. Screw driver bit
11. Operator’s manual
12. Battery pack
13. Charger

MAINTENANCE

Ŷ

The product should never be connected to a power 

VXSSO\ ZKHQ DVVHPEOLQJ SDUWV PDNLQJ DGMXVWPHQWV

cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product from the power 
supply will prevent accidental starting that could cause