GRAPHITE 58G012-S15 - Инструкция по эксплуатации - Страница 14

14

HOLDER

The power tool provides convenient holder (

6

) that allows to e.g. 

hang the tool on a tool belt when working at heights.

OPERATION AND MAINTENANCE

MAINTENANCE AND STORAGE

•

Cleaning the device after each use is recommended.

•

Do not use water or any other liquid for cleaning.

•

Clean the power tool, battery and charger with a dry cloth or 

blow through with compressed air at low pressure. 

•

Do not use any cleaning agents or solvents, they may damage 

plastic parts.

•

Clean ventilation holes in the motor casing regularly to 

prevent device overheating.

•

In case of excessive commutator sparking, have the technical 

condition of carbon brushes of the motor checked by a 

qualified person.

•

Store the power tool and its equipment in a dry place, beyond 

reach of children.

•

Store the device with the battery removed.

All defects should be repaired by service workshop authorized 

by the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS

Cordless impact driver 

Parameter

Value

Battery voltage

18V DC

Range of idle rotational speed

0-2200 min

-1

Tool chuck

6,35 mm (¼ ‘’)

Max. torque

180 Nm

Protection class

III

Weight 

1,2 kg

Year of production

2021

Graphite Energy+ System Battery

Parameter

Value

Battery

58G001

58G004

Battery voltage

18 V DC

18 V DC

Battery type

Li-Ion

Li-Ion

Battery capacity 

2000 mAh

4000 mAh

Ambient temperature range

4

0

C – 40

0

C

4

0

C – 40

0

C

Charging time for charger 58G002

1 h

2 h

Weight 

0,400 kg

0,650 kg

Year of production

2021

2021

Graphite Energy+ System Charger

Parameter

Value

Charger type

58G002

Supply voltage

230 V AC

Power supply frequency

50 Hz

Charging voltage

22 V DC

Max. charging current

2300 mA

Ambient temperature range

4

0

C – 40

0

C

Charging time of the battery 58G001

1 h

Charging time of the battery 58G004

2 h

Protection class

II

Weight 

0,300 kg

Year of production

2021

NOISE LEVEL AND VIBRATION PARAMETERS
Noise and vibration information

Parameters of produced noise level, such as sound pressure level 

Lp

A

 and sound power level Lw

A

 with measurement uncertainty K 

are specified below in this manual, in compliance with EN 60745. 

Vibration values a

h

 and measurement uncertainty K are 

determined in accordance with EN 60745-2-2 and specified 

below.

Vibration level specified below in this manual was measured in 

accordance with measurement procedure defined in EN 60745 

and can be used to compare power tools. It can also be used for 

initial assessment of exposure to vibrations. 

Specified vibration level is representative for main applications 

of the power tool. Vibration level may change if the power tool is 

used for other purposes, with different working tools or will not 

be maintained properly. The abovementioned factors may lead 

to higher exposure to vibrations during whole working time.   

To precisely define exposure to vibrations, include periods when 

the power tool is switched off and when it is switched on but 

not used for working. This way total exposure to vibrations may 

be significantly lower. Use additional safety measures to protect 

the user against results of exposure to vibrations, such as: power 

tool and working tool maintenance, proper hand temperature 

conditions, good work organisation. 
Sound pressure level: Lp

A 

= 95,1 dB (A) K=3dB (A)

Sound power level: Lw

A 

= 106,1  dB (A) K=3dB (A)

Vibration acceleration: a

h 

= 15,87 m/s

2

  K = 1,5 m/s

2

ENVIRONMENTAL PROTECTION

Electrical equipment must not be disposed off 

with household waste and, instead, should be 

utilized at appropriate facilities. Information 

on utilization can be provided by the product 

vendor or the local authorities. Waste electrical 

and electronic equipment contains substances 

that are not neutral to the natural environment. 

Equipment that is not recycled constitutes a 

potential hazard to the environment and to 

human health.

Li-Ion

Do not dispose the batteries with household 

wastes, do not throw in fire or water. Damaged 

or worn out batteries should be properly recycled 

in accordance with applicable directive for 

battery disposal.. Batteries should be returned to 

collection points fully discharged, if the batteries 

are not completely discharged, they must be 

protected against short circuits. Used batteries 

can be returned free of charge at commercial 

locations. The buyer of the goods is obliged to 

return the used batteries.

* Right to introduce changes is reserved.

“Grupa Topex Spółka z ograniczoną odpowiedzialnością” Spółka 

komandytowa with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa 

Topex) informs, that all copyrights to this instruction (hereinafter Instruction), 

including, but not limited to, text, photographies, schemes, drawings 

and layout of the instruction, belong to Grupa Topex exclusively and are 

protected by laws accordingly to Copyright and Related Rights Act of 4 

February 2004 (ustawa o prawie autorskim i prawach pokrewnych, Dz. U. 2006 

No 90 item 631 with later ammendments). Copying, processing, publishing, 

modifications for commercial purposes of the entire Instruction or its parts 

without written permission of Grupa Topex are strictly forbidden and may 

cause civil and legal liability.