DWT BM-1050 M 5.1.6 - Инструкция по эксплуатации - Страница 16

16

English

Service

•

Have  your  power  tool  serviced  by  a  qualified 

repair  person  using  only  identical  replacement 

parts.

 This will ensure that the safety of the power tool 

is maintained�

•

Follow instruction for lubricating and changing ac-

cessories�

•

Special 

safety warnings

Use auxiliary handle(s), if supplied with the tool. 

Loss of control can cause personal injury�

•

Hold power tool by insulated gripping surfaces, 

when  performing  an  operation  where  the  cutting 

accessory  may  contact  hidden  wiring  or  its  own 

cord.

 Cutting accessory contacting a "live" wire may 

make exposed metal parts of the power tool "live" and 

could give the operator an electric shock�

•

Safety guidelines during 

power tool operation

The workpiece shall be fastened� Fixed devices or 

vice shall be used to fasten the workpiece, which will 

be more secure than holding the workpiece with your 

hands�

•

Considering that asbestos may cause cancer, as-

bestos-containing materials shall not be processed�

•

The power tool could be put down only after the 

parts of power tool is completely static� Accessory on 

the power tool might be clamped during work, which 

may make it difficult for you to control the power tool.

•

Power tool with damaged electric wires shall not be 

used� If electric wires of the power supply are dam-

aged during the work, you shall not touch the damaged 

electric wires and shall pull out the plug immediately� 

Damaged electric wires will raise the risk of electric 

shock�

•

When using power tools outdoor, you must install 

fault current (FI) protection switch on the power tool�

• Appropriate detector shall be used to find the loca

-

tion of hidden power wires� Or you should obtain rel-

evant information from local power supply unit� Drill-

ing  electric  wires  will  cause  fire  and  electric  shock. 

Damaged gas pipe will cause exploration� If water 

pipes are punctured, damage will be caused to prop-

erty�

•

In case a accessory installed on the power tool is 

clamped, you shall shut down the power tool and stay 

calm� At that time, the power tool will produce extreme-

ly high reactive torque thus resulting in return stroke� 

The accessory installed on the power tool are likely to 

be clamped, for example: hypercharge of power tool or 

skewing of accessory installed on the power tool dur-

ing work�

•

If hidden electric wires or power lines of the power 

tool itself might be cut off during work, you must hold 

the insulated handle to operate the power tool� When 

the power tool is in touch with a charged line, the metal 

parts on the power tool will conduct electricity and may 

cause the operator to get an electric shock�

•

During work, you must tightly hold the power tool 

and ensure you stand firmly. You should hold the pow

-

er tool with your hands�

•

When operating and using the power tool, you can 

only hold switch position of the main handle rather than 

other parts�

•

Avoid stopping an power tool motor when loaded�

•

In case the power tool should fall into the stirred so-

lution, switch off the plug immediately and have the 

power tool checked by a service center� Material that 

has penetrated into the power tool can cause damage 

and lead to an electric shock�

•

Do not use the power tool for explosive materials (e� 

g., easily inflammable solvents).

•

Take protective measures if combustible or explo-

sive dust, harmful to one's health, may appear during 

working�

•

Always wait until the power tool has come to a com-

plete stop before unhand it�

•

Never remove any chips or fragments with your 

power tool's motor running�

•

When working, follow the position of the power sup-

ply cable� Avoid winding it around your legs or arms� 

•

Use only sharp drills without defects - it will make 

working with the power tool easier�

•

Do not apply excessive pressure when operating 

the power tool - it can jam the drill and overload the 

engine�

•

Do not allow drills to jam in the material processed� 

If this occurs, do not try to release them by means of 

the power tool engine� This can put the power tool out 

of order�

•

Striking out drills jammed in the material processed 

with a hammer or other objects is strictly forbidden - 

metal fragments can hurt both the operator and the 

people nearby�

•

Avoid overheating your power tool, when using it for 

a long time�

Symbols used in 

the manual

Following symbols are used in the operation manual, 

please remember their meanings� Correct interpreta-

tion of the symbols will allow correct and safe use of 

the power tool�

Symbol

Meaning

Low speed drill

Sections marked gray - soft  

grip (with insulated surface)�

Serial number sticker:

BM ��� - model;

XX - date of manufacture;

XXXXXXX - serial number�

Possibility to select between 

three positions of additional 

handle�