CROWN CT21072HX-2 BMC - Инструкция по эксплуатации - Страница 23

23

English

•

Keep  cutting  tools  sharp  and  clean.

 Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control�

•

Use  the  power  tool,  accessories  and  tool  bits 

etc.  in  accordance  with  these  instructions,  taking 

into account the working conditions and the work 

to be performed. 

Use of the power tool for operations 

different from those intended could result in a hazard-

ous situation�

•

Keep  handles  and  grasping  surfaces  dry,  clean 

and  free  from  oil  and  grease.

 Slippery handles and 

grasping surfaces do not allow for safe handling and 

control of the tool in unexpected situations�

•

Note that when you operate a power tool, please 

hold the auxiliary handle correctly, which is helpful 

when controlling the power tool� Therefore, proper 

holding can reduce the risk of accidents or injuries�

Battery tool use and care

•

Recharge only with the charger specified by the 

manufacturer.

 A charger that is suitable for one type 

of battery pack may create a risk of fire when used with 

another battery pack�

•

Use power tools only with specifically designat

-

ed battery packs.

 Use of any other battery packs may 

create a risk of injury and fire.

•

When  battery  pack  is  not  in  use,  keep  it  away 

from  other  metal  objects,  like  paper  clips,  coins, 

keys,  nails,  screws  or  other  small  metal  objects, 

that  can  make  a  connection  from  one  terminal  to 

another. 

Shorting the battery terminals together may 

cause burns or a fire.

•

Under abusive conditions, liquid may be ejected 

from  the  battery;  avoid  contact.  If  contact  acci

-

dentally occurs, flush with water. If liquid contacts 

eyes, additionally seek medical help. 

Liquid ejected 

from the battery may cause irritation or burns�

•

Avoid  unintentional  switching  on.  Ensure  the 

on / off switch is in the off position before inserting 

battery pack.

 Carrying the power tool with your finger 

on the on / off switch or inserting the battery pack into 

power tools that have the switch in accidents�

•

Do not open the battery.

 Danger of circuit�

•

In  case  of  damage  and  improper  use  of  the 

battery,  vapors  may  be  emitted.  Provide  for  fresh 

air  and  seek  medical  help  in  case  of  complaints.

The vapors can irritate the respiratory system�

•

When the battery is defective, liquid can escape 

and come into contact with adjacent components

� 

Check any parts concerned� Clean such parts or 

replace them, if required�

•

Protect  the  battery  against  heat,  e.g.,  also 

against  continuous  sun  irradiation  and  fire.

 There 

is danger of explosion�

WARNING! Read all safety warnings and 

all instructions.

•

Protect  the  battery  charger  from  rain  and 

moisture. 

The penetration of water in a battery 

charger increases the risk of electric shock�

•

Do not charge other batteries.

 The battery charger 

is suitable only for charging lithium ion batteries within 

the listed voltage range� Otherwise there is danger of 

fire and explosion.

•

Keep  the  battery  charger  clean.

 Contamination 

may cause the danger of electric shock�

•

Check the battery charger, cable and plug each 

time before using. Do not use the battery charger 

when  defects  are  detected.  Do  not  open  the 

battery charger yourself and have it repaired only 

by  qualified  personnel  using  original  spare  parts.

Damaged battery chargers, cables and plugs increase 

the risk of electric shock�

•

Do  not  operate  the  battery  charger  on  easily  in

-

flammable  surfaces  (e.g.  ,  paper  ,  textiles  ,  etc.)  or 

in combustible environments.

 There is danger of fire 

due to the heating of the battery charger during charging�

Service

•

Have  your  power  tool  serviced  by  a  qualified 

repair  person  using  only  identical  replacement 

parts.

 This will ensure that the safety of the power tool 

is maintained�

•

Follow instruction for lubricating and changing ac-

cessories�

Special safety warnings

•

Hold power tool by insulated gripping surfaces, 

when  performing  an  operation  where  the  cutting 

accessory  may  contact  hidden  wiring  or  its  own 

cord.

 Cutting accessory contacting a "live" wire may 

make exposed metal parts of the power tool "live" and 

could give the operator an electric shock�

•

Wear ear protectors Exposure to noise can cause 

hearing loss�

Safety  guidelines  during  power  tool 

operation

•

The workpiece shall be fastened� Fixed devices or 

vice shall be used to fasten the workpiece, which will 

be more secure than holding the workpiece with your 

hands�

•

Considering that asbestos may cause cancer, as-

bestos - containing materials shall not be processed�

•

The power tool could be put down only after the 

parts of power tool is completely static� Accessory on 

the power tool might be clamped during work, which 

m

ay make it difficult for you to control the power tool.

•

Appr

opriate detector shall be used to find the loca

-

tion of hidden power wires� Or you should obtain rel-

evant information from local power supply unit� Drilling 

electric  wires  will  cause  fire  and  electric  shock.  Dam

-

aged gas pipe will cause exploration� If water pipes are 

punctured, damage will be caused to property�

•

In case a accessory installed on the power tool is 

clamped, you shall shut down the power tool and stay 

calm� At that time, the power tool will produce extreme-

ly high reactive torque thus resulting in return stroke� 

The accessory installed on the power tool are likely to 

be clamped, for example: hypercharge of power tool or 

skewing of accessory installed on the power tool dur-

ing work�

•

If hidden electric wires or power lines of the power 

tool itself might be cut off during work, you must hold 

the insulated handle to operate the power tool� When 

the power tool is in touch with a charged line, the metal 

parts on the power tool will conduct electricity and may 

cause the operator to get an electric shock�

•

During work, you must tightly hold the power tool 

and ensure you stand firmly. You should hold the pow

-

er tool with your hands�