Bosch GPO 14 CE - Инструкция по эксплуатации - Страница 17

18

 | English 

1 619 P09 071 | (29.6.10)

Bosch Power Tools

f

Do not use a damaged accessory. Before 
each use inspect the accessory such as 
abrasive wheels for chips and cracks, back-
ing pad for cracks, tear or excess wear, wire 
brush for loose or cracked wires. If power 
tool or accessory is dropped, inspect for 
damage or install an undamaged accessory. 
After inspecting and installing an accesso-
ry, position yourself and bystanders away 
from the plane of the rotating accessory 
and run the power tool at maximum no-load 
speed for one minute. 

Damaged accessories 

will normally break apart during this test 
time.

f

Wear personal protective equipment. De-
pending on application, use face shield, 
safety goggles or safety glasses. As appro-
priate, wear dust mask, hearing protectors, 
gloves and workshop apron capable of stop-
ping small abrasive or workpiece frag-
ments. 

The eye protection must be capable 

of stopping flying debris generated by vari-
ous operations. The dust mask or respirator 
must be capable of filtrating particles gener-
ated by your operation. Prolonged exposure 
to high intensity noise may cause hearing 
loss.

f

Keep bystanders a safe distance away from 
work area. Anyone entering the work area 
must wear personal protective equipment. 

Fragments of workpiece or of a broken ac-
cessory may fly away and cause injury be-
yond immediate area of operation.

f

Hold power tool by insulated gripping sur-
faces only, when performing an operation 
where the cutting accessory may contact 
hidden wiring or its own cord. 

Cutting ac-

cessory contacting a “live” wire may make ex-
posed metal parts of the power tool “live” 
and shock the operator.

f

Position the cord clear of the spinning ac-
cessory. 

If you lose control of the power tool, 

the cord may be cut or snagged and your 
hand or arm may be pulled into the spinning 
accessory.

f

Never lay the power tool down until the ac-
cessory has come to a complete stop. 

The 

spinning accessory may grab the surface and 
pull the power tool out of your control.

f

Do not run the power tool while carrying it 
at your side. 

Accidental contact with the 

spinning accessory could snag your clothing, 
pulling the accessory into your body.

f

Regularly clean the power tool’s air vents.  

The motor’s fan will draw the dust inside the 
housing and excessive accumulation of pow-
dered metal may cause electrical hazards.

f

Do not operate the power tool near flamma-
ble materials. 

Sparks could ignite these ma-

terials.

f

Do not use accessories that require liquid 
coolants. 

Using water or other liquid cool-

ants may result in electrocution or shock.

Kickback and related warnings

f

Kickback is a sudden reaction to a pinched or 
snagged rotating wheel, backing pad, brush 
or any other accessory. Pinching or snagging 
causes rapid stalling of the rotating accesso-
ry which in turn causes the uncontrolled 
power tool to be forced in the direction op-
posite of the accessory’s rotation at the 
point of the binding.
For example, if an abrasive wheel is snagged 
or pinched by the workpiece, the edge of the 
wheel that is entering into the pinch point 
can dig into the surface of the material caus-
ing the wheel to climb out or kick out. The 
wheel may either jump toward or away from 
the operator, depending on direction of the 
wheel’s movement at the point of pinching. 
Abrasive wheels may also break under these 
conditions.
Kickback is the result of power tool misuse 
and/or incorrect operating procedures or 
conditions and can be avoided by taking 
proper precautions as given below.

OBJ_BUCH-1284-001.book  Page 18  Tuesday, June 29, 2010  12:51 PM