Bosch 0.601.64L.902 - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

1 609 92A 0BG | (25.10.13)

Removing the Saw Blade (see figure C)

Turn the locking sleeve 

3

 approx. 90 °  in the direction of the 

arrow and hold. Remove the saw blade 

1

.

Dust/Chip Extraction



Dusts from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health. Touching or breathing-in the dusts can cause 
allergic reactions and/or lead to respiratory infections of 
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered 
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials 
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.

Operation

Starting Operation

Inserting the battery



Use only original Bosch lithium ion batteries with the 
voltage listed on the nameplate of your power tool. 

Using 

other batteries can lead to injuries and pose a fire hazard.

Push the lock-off button 

6

 leftward to protect the power tool 

against accidental switching on.

Insert the charged battery 

12

 into the handle until it can be 

felt to engage and faces flush against the handle.

Switching On and Off (see figure D)

Push the lock-off button 

6

 rightward.

To 

start

 the machine, press the On/Off switch 

7

 and keep it 

pressed.

To 

switch off

 the machine, release the On/Off switch 

7

.

Afterwards, push the lock-off button 

6

 leftward again.

To save energy, only switch the power tool on when using it.

Controlling the Stroke Rate

Increasing or reducing the pressure on the On/Off switch 

7

 ena-

bles stepless stroke-rate control of the switched-on machine.

The required stroke rate is dependent on the material and the 
working conditions and can be determined by a practical trial.

Reducing the stroke rate is recommended when the saw 
blade engages in the material as well as when sawing plastic 
and aluminium.

Temperature Control/Overload Protection Indicator

The red LED indicator 

10

 will help you in protecting the bat-

tery against overheating and the motor against overloading.

When the LED indicator 

10

continuously lights up red

, the 

temperature of the battery is too high and the machine 
switches off automatically.
– Switch the power tool off.
– Allow the battery to cool down before continuing to work.

The LED indicator 

10

flashes red

, the power tool is blocked 

and switches off automatically.
– Remove the power tool from the workpiece.

As soon as the blockage is corrected, the power tool will 
continue to work at the set stroke rate.

Protection Against Deep Discharging

The lithium ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.

Working Advice



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.

Tips



When sawing light building materials, observe the stat-
utory provisions and the recommendations of the ma-
terial suppliers.

Check wood, press boards, building materials, etc. for foreign 
objects such as nails, screws or similar, and remove them, if 
required.
Switch the machine on and guide it toward the workpiece. 
Position the base plate

 2 

 onto the surface of the work and saw 

through the material applying uniform contact pressure and 
feed. After completing the working procedure, switch the 
machine off.
If the saw blade should jam, switch the machine off immedi-
ately. Widen the gap somewhat with a suitable tool and pull 
out the machine.

Plunge Cutting (see figure E)



The plunge cutting procedure is only suitable for treat-
ing soft materials such as wood, plaster board or simi-
lar! Do not work metal materials with the plunge cut-
ting procedure!

Use only short saw blades for plunge cutting.
Place the machine with the edge of the footplate 

2

 onto the 

workpiece and switch on. For power tools with stroke speed 
control, set the maximum stroke speed. Press the power tool 
firmly against the workpiece and allow the saw blade to slowly 
plunge into the workpiece.
As soon as the footplate 

2

 fully lays on the surface of the work-

piece, continue sawing alongside the desired cutting line.
For certain work, the saw blade 

1

 can also be inserted turned 

through by 180 °  and the sabre saw can be guided accordingly 
in a reversed manner.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be applied 
alongside cutting line because of the material heating up.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.
Store the battery only within a temperature range between 
0 ° C and 50 ° C. As an example, do not leave the battery in the 
car in summer.

OBJ_BUCH-1272-004.book  Page 15  Friday, October 25, 2013  2:19 PM