Bosch GOP 300 SCE - Инструкция по эксплуатации - Страница 16

16

 | English 

2 609 932 934 | (8.10.14)

Bosch Power Tools

Selecting the Application Tool/Accessory

Mounting/Replacing the Application Tool/Accessory 

(GOP 250 CE)

If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory, loosen the 
screw 

7

 with the hex key 

8

 and remove the application 

tool/accessory.
Mount the requested application tool/accessory (e. g. plunge 
cut saw blade 

6

) in such a manner on the tool holder 

4

 that the 

offset faces downward (see illustration on the graphics page; 
marking on the application tool/accessory is readable from 
above).
Turn the application tool/accessory to a position favourable 
for the respective job, and allow it to engage into the cams of 
the tool holder 

4

. 12 different positions are possible, each 

offset by 30 °.

For more intermediate positions, the adapter 

9

 (accessory) 

can be used: Allow the adapter to engage with the smooth 
side onto the cams of the tool holder 

4

 (see illustration on the 

graphics page). Position the application tool/accessory onto 
the adapter in any position.

Fasten the application tool/accessory with bolt 

7

. Tighten the 

bolt with hex key 

8

 until the spring washer of the bolt faces 

flush against the application tool/accessory.



Check the tight seating of the application tool/accesso-

ry. 

Incorrect or not securely fastened application tools/ac-

cessories can come loose during operation and pose a haz-
ard.

Mounting/Replacing the Application Tool/Accessory 

(GOP 300 SCE)

If required, remove an already mounted application tool/
accessory.

For this, open the SDS lever 

12

 to the stop (not further) and 

remove the application tool.

Mount the requested application tool/accessory (e. g. plunge 
cut saw blade 

6

) in such a manner on the tool holder 

4

 that the 

offset faces downward (see illustration on the graphics page; 
marking on the application tool/accessory is readable from 
above).

Turn the application tool/accessory to a position favourable 
for the respective job, and allow it to engage into the cams of 
the tool holder 

4

. 12 different positions are possible, each 

offset by 30 °.

Close SDS lever 

12

 so that it faces against the housing of the 

power tool.



Check the tight seating of the application tool/accesso-

ry. 

Incorrect or not securely fastened application tools/ac-

cessories can come loose during operation and pose a haz-
ard.

Mounting/Replacing a Sanding Sheet on the Sanding 

Plate

The sanding plate 

10

 is fitted with Velcro backing for quick 

and easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 

11

, free the Velcro back-

ing of the sanding plate 

10

 from any debris by tapping against 

it in order to enable optimum adhesion.

Position the sanding sheet 

11

 flush alongside one edge of the 

sanding plate 

10

, then lay the sanding sheet onto the sanding 

plate and press firmly.

To ensure optimum dust extraction, pay attention that the 
punched holes in the sanding sheet match with the holes in 
the sanding plate.

To remove the sanding sheet 

11

, grasp it at one of the tips and 

pull it off from the sanding plate 

10

.

You can use all sanding sheets, fleece pads/polishing cloth 
pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth 
pads, are attached to the sanding plate in the same manner.

Accessory

Material

HCS wood seg-
ment saw blade*

Wooden materials, 
plastic

BIM segment saw 
blade*

Wooden materials, 
plastic, non-ferrous 
metals

HCS plunge cut 
saw blades, 
wood*

Wooden materials, 
plastic, gypsum and 
other soft materials

BIM plunge cut 
saw blades, 
metal *

Metal (e. g. unhard-
ened nails, screws, 
smaller profiles), 
non-ferrous metals

BIM plunge cut 
saw blade, wood 
and metal *

Wood, metal, non-
ferrous metals

HM-Riff segment 
saw blade*

Grouting joints, soft 
wall tiles, glass-fibre 
reinforces plastic 
and other abrasive 
materials

HM-Riff delta 
plate *

Scraper, rigid *

Carpets, coverings

Scraper, flexible * Silicone and other 

elastic materials

Base plate for 
sanding, series 
Delta 93 mm*

Depends on sanding 
sheet 

* Optional accessory; for the complete accessories please see Bosch 
accessory programme.

OBJ_BUCH-1271-005.book  Page 16  Wednesday, October 8, 2014  11:11 AM