Bosch GOP 18V-28 - Инструкция по эксплуатации - Страница 23

To sand corners, edges and hard-to-reach areas accurately,
you can also work with the tips alone or with an edge of the
sanding plate.
The sanding sheet may heat up significantly when used to
sand specific points rather than entire surfaces. Reduce the
orbital stroke rate and contact pressure and allow the sand-
ing sheet to cool down at regular intervals.
Do not use a sanding sheet for other materials after it has
been used to work on metal.
Use only original Bosch sanding accessories.
Always connect a dust extraction system for sanding.

Scraping

Select a high orbital stroke rate level for scraping.
Work on a soft surface (e.g. wood) at a flat angle and with
low contact pressure. Failure to do so may cause the scraper
to cut into the surface underneath.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the speed is reduced
or the power tool switches off. At reduced speed, the power
tool will run again at full speed once the permitted battery
temperature is reached or the load is reduced. If it automat-
ically shuts down, switch the power tool off, allow the bat-
tery to cool down, then switch the power tool back on.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.

Maintenance and Servicing

Maintenance and cleaning

u

Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.

 There is risk of injury

from unintentionally pressing the on/off switch.

u

To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.

Regularly clean Riff application tools (accessories) using a
wire brush.

After-sales service and advice on using products

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: 

www.bosch-pt.com

The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.) 
P.O. Box 98 
Broadwater Park 
North Orbital Road 
Denham Uxbridge
UB 9 5HJ 
At 

www.bosch-pt.co.uk

 you can order spare parts or ar-

range the collection of a product in need of servicing or re-
pair. 
Tel. Service: (0344) 7360109 
E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd. 
Unit 23 Magna Drive 
Magna Business Park 
City West 
Dublin 24 
Tel. Service: (01) 4666700 
Fax: (01) 4666888

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd. 
Power Tools 
Locked Bag 66 
Clayton South VIC 3169 
Customer Contact Center 
Inside Australia: 
Phone: (01300) 307044 
Fax: (01300) 307045
Inside New Zealand: 
Phone: (0800) 543353 
Fax: (0800) 428570
Outside AU and NZ: 
Phone: +61 3 95415555 
www.bosch-pt.com.au 
www.bosch-pt.co.nz

Republic of South Africa
Customer service

Hotline: (011) 6519600

Gauteng – BSC Service Centre

35 Roper Street, New Centre 
Johannesburg 
Tel.: (011) 4939375 
Fax: (011) 4930126 
E-mail: bsctools@icon.co.za

KZN – BSC Service Centre

Unit E, Almar Centre 
143 Crompton Street 
Pinetown 
Tel.: (031) 7012120 

English | 

23

Bosch Power Tools

1 609 92A 4DA | (08.10.2018)