Einhell TC-TS 315 - Инструкция по эксплуатации - Страница 35

GB

- 35 -

of the saw blade can be readjusted for 0°. To 

do this, adjust the adjustment screw (47).

7.6  Accessory slide used as an angle stop/

cross stop (Fig. 27)

•

 The slide can be used as an angle stop/cross 

stop in the same way as the universal stop 

(see 6.8).

•

 Slacken the clamping lever (106).

•

 Turn the stop rail (101) until the desired angle 

is reached. 0° for use as a cross stop (90° 

cuts) – a different angle for angle cuts.

•

 Retighten the clamping lever (106).

•

 Important! Do not push the stop rail too far 

toward the blade (5). The distance between 

the stop rail and the blade should be approx. 

2 cm.

 8. Operation

Warning! 

•

 After every new adjustment we recommend 

you to make a trial cut in order to check the 

new settings.

•

 After switching on the saw, wait for the blade 

to reach its maximum speed of rotation before 

commencing with the cut.

•

 Take extra care when starting the cut!

•

 Never use the equipment without the suction

function. 

•

Regularly check and clean the suction chan-

nels.

8.1  Making longitudinal cuts (Figure 17)

Longitudinal cutting (also known as slitting) is 

when you use the saw to cut along the grain of the 

wood. Press one edge of the workpiece against 

the parallel stop (7) while the 

fl

 at side lies on the 

saw table (1). The guard hood (2) must always be 

lowered over the workpiece.

When you make a longitudinal cut, never adopt 

a working position that is in line with the cutting 

direction.

•

 Set the parallel stop (7) in accordance with 

the workpiece height and the desired width. 

(See 7.3.)

•

 Switch on the saw.

•

 Place your hands (with fingers closed) flat on 

the workpiece and push the workpiece along 

the parallel stop (7) and into the blade (4).

•

Provide guidance at the side with your hand 

only as far as the front edge of the guard 

hood. 

•

Always push the workpiece through to the 

end of the splitter (5).

•

 The offcut piece remains on the saw table 

(1) until the blade (4) is back in its position of 

rest.

•

 Secure long workpieces against falling off 

at the end of the cut (e.g. with a roller stand 

etc.).

8.1.1 Cutting narrow workpieces (Fig. 18)

Be sure to use a push stick (3) when making 

longitudinal cuts in workpieces smaller than 150 

mm in width. A push stick is supplied with the 

saw! Replace a worn or damaged push stick im-

mediately.

8.1.2 Cutting very narrow workpieces  

(Fig. 19)

•

Be sure to use a push block (10) when ma-

king longitudinal cuts in very narrow workpie-

ces with a width of 50 mm and less.

•

The low guide face of the parallel stop is best 

used in this case.

•

The push block (10) is supplied with the saw.

•

Replace the push block without delay when it 

becomes worn.

8.2  Making bevel cuts (Fig. 16/20)

Bevel cuts must always be used using the parallel 

stop (7).

•

 Set the blade (4) to the desired angle. (See 

7.5.)

•

 Set the parallel stop (7) in accordance with 

the workpiece width and height (see 7.3)

•

 Carry out the cut in accordance with the work-

piece width (see 8.1.1. and 8.1.2)

8.3  Making cross cuts (Figs. 21, 27)

Cross cuts must always be performed using the 

holder (24) together with the stop rail (23) as a 

cross stop (see 7.4); in addition, cross cuts can 

also be performed using the accessory slide as a 

cross stop (see 7.6). In this case the workpiece is 

cut through crosswise.

•

 Set the cross stop or accessory slide to the 

desired angle (see 7.4 or 7.6).

•

 Press the workpiece firmly against the stop 

rail (23 or 101).

•

 Switch on the saw.

•

 Push the cross stop or accessory slide and 

the workpiece toward the blade in order to 

make the cut.

•

 Warning! Always hold the guided part of the 

workpiece. Never hold the part which is to be 

cut off.

Anl_TC_TS_315_U_SPK9-1.indb   35

Anl_TC_TS_315_U_SPK9-1.indb   35

23.03.2020   09:16:58

23.03.2020   09:16:58