Einhell TC-TS 315 - Инструкция по эксплуатации - Страница 34

GB

- 34 -

speed of rotation before commencing with 

the cut.

•

To turn the equipment off again, press the red 

button „0“.

Overload cut-out (Fig. 23)

The motor of this equipment is protected against 

overload by an overload switch (52). If the rated 

current is exceeded, the overload switch (52) will 

shut down the equipment.

•

Let the equipment cool down for several mi-

nutes.

•

Press the overload switch (52).

•

Press the green button „I“ to switch on the 

equipment.

7.2  Cutting depth (Fig. 1)

Turn the hand crank (8) to set the blade (4) to the 

required cutting depth.

Turn anti-clockwise:  

larger cutting depth

Turn clockwise:  

smaller cutting depth

7.3. Parallel stop

7.3.1 Stop height (Fig. 12-14, 2b)

•

Use the holder (24) together with the parallel 

stop rail (23) as a parallel stop.

•

The parallel stop supplied with the bench-ty-

pe circular saw has two different guide faces. 

•

 For thick material you must use the stop rail 

(23) as shown in Fig. 12, for thin material you 

must use the stop rail as shown in Fig.13.

•

 To change over the stop rail (23) to the lo-

wer guide face you have to slacken the two 

knurled screws (26) in order to disconnect the 

stop rail (23) from the holder (24).

•

 Remove the two knurled screws (26) through 

the one slot (25) in the stop rail (23) and in-

sert in the other slot (27).

•

 Remount the stop rail (23) on the holder (24).

•

 The procedure for changing over to the high

guide face is similar.

7.3.2 Cutting width (Fig. 12/13)

•

The parallel stop (7) has to be used when 

making longitudinal cuts in wooden workpi-

eces.

•

The parallel stop (7) can be mounted on the 

right-hand side of the saw table (1).

•

The parallel stop (7) has to be mounted in the 

guide rail (28) of the saw table (1).

•

The parallel stop (7) can be set to the requi-

red dimension with the help of the scale (22) 

on the table.

•

Use the locking grip (12) to secure the paral-

lel stop (7) in the guide rail (28) and hence the 

desired cutting width.

7.3.3 Setting the stop length (Fig. 14)

•

 The stop rail (23) can be moved in longitudi-

nal direction in order to prevent the workpiece 

from becoming jammed.

•

 Rule of thumb: The rear end of the stop co-

mes up against an imaginary line that begins 

roughly at the center of the blade and runs at 

an angle of 45° to the rear.

•

 Set the required cutting width 

- Slacken the knurled screws (26) and push 

the stop rail (23) forward until it touches the

imaginary 45° line. 

- Retighten the knurled screws (26).

Warning!

 The gap between the saw table (1) and 

the underside of the stop rail (23) must not be too 

large in order to prevent the material getting jam-

med. To adjust the distance, the parallel stop (7) 

must be fastened 

fi

 rst using the locking grip (12). 

Then slacken the knurled screws (26), lower the 

stop rail (23) down to the saw table (1) and secu-

re the knurled screws (26) again afterwards.

7.4  Cross stop (Fig. 15)

•

 Use the holder (24) together with the cross 

stop rail (23) as a cross stop.

•

 Slide the cross stop into the guide rail (41) on 

the left-hand side on the saw table.

•

 Undo the locking grip (20).

•

 Turn the stop rail (23) until the arrow points to 

the angle required.

•

 Re-tighten the locking grip (20).

Important!

•

 Do not push the stop rail (23) too far toward 

the blade.

•

 The distance between the stop rail (23) and 

the blade (4) should be approx. 2 cm.

7.5  Setting the angle (Fig. 16)

•

 Slacken the locking grip (9) at the front and 

rear of the housing (44).

•

 Move the housing (44) until the pointer (46) 

points to the desired angular setting on the 

scale (45).

•

 Lock this setting with the locking grip (9) at 

the front and rear of the housing (44).

•

 If needed, the end stop for adjusting the angle 

Anl_TC_TS_315_U_SPK9-1.indb   34

Anl_TC_TS_315_U_SPK9-1.indb   34

23.03.2020   09:16:57

23.03.2020   09:16:57