Einhell TC-TS 315 - Инструкция по эксплуатации - Страница 32

GB

- 32 -

in the same way as the guide rail for the par-

allel stop. The guide rail (41) should be in the 

middle of the saw table (1).

•

 Then tighten all the loose screw connections.

Important! Select a height for the guide rails

which ensures that: 

•

 they are parallel to the saw table,

•

 the parallel stop (7) is not blocked by the saw 

table (1) when pushed,

•

 but that the gap between the guide rail and 

parallel stop (7) is not too large.

6.3  Fitting/removing the table insert (Fig. 6)

•

 To prevent increased likelihood of injury, the 

table insert should be changed whenever it is 

worn or damaged.

•

 Take off the saw blade guard (2) (6.5).

•

 Remove the countersunk head screw (17).

•

 Take out the worn table insert (6).

•

 To fit the replacement table insert, proceed in 

reverse order.

6.4  Fitting/removing the splitter (Figs. 7-9)

•

 Danger! Pull out the power plug.

•

 Set the blade (4) to max. cutting depth, move 

to 0° position and lock in place.

•

 Remove the saw blade guard (see 6.5).

•

 Take out the table insert (6) (see 6.3).

•

 Slacken the fixing screw (19). Important! Sla-

cken the fastening screw (19) only as far as 

necessary until the gap (14) is approx. 5 mm. 

The fastening screw (19) does not have to be 

removed to fit the splitter (5).

•

 Insert the splitter (5) into the gap (14). Make 

sure that the splitter has been fitted straight 

and not wobbly.

•

 The splitter (5) must be positioned in the cen-

ter along an imaginary line extending behind 

the saw blade (4), so that it is not possible for 

the material to get jammed.

•

 The distance between the blade (4) and the 

splitter (5) should be 3-8 mm.

•

 Retighten the fastening screw (19) and fit the 

table insert (6) and saw blade guard (2).

•

 The splitter (5) must not be set to a depth of 

more than 2 mm relative to the saw blade in 

the vertical direction.

•

 To dismantle, proceed in reverse order.

6.5  Fitting/removing the saw blade guard

(Figs. 1, 5)

•

 Mount the saw blade guard (2) on the splitter 

(5) so that the screw fits through the hole (18) 

in the splitter.

•

 Do not tighten the screw (15) and locking grip 

(48) too far – the saw blade guard must be 

able to move freely.

•

 To dismantle, proceed in reverse order.

Warning! The saw blade guard (2) must al-

ways be lowered over the workpiece before 

you begin to cut.

6.6  Fitting/changing the saw blade  

(Figs. 10/11)

•

 Before changing the saw blade: Pull out the 

power plug!

•

 Wear work gloves to prevent injury when 

changing the saw blade.

•

 Set the blade (4) to max. cutting depth, move 

to 0° position and lock in place.

•

 Remove the saw blade guard (2), table insert 

(6) and splitter (5) (see 6.5, 6.3, 6.4).

•

 Place the face spanner (33) on the saw blade 

flange (40) to apply counter-pressure and 

undo the screw with the ring wrench (37).

•

 Caution! Turn the screw in the direction of ro-

tation of the saw blade.

•

 Take off the outer flange and pull the old saw 

blade (4) off the inner flange.

•

 Clean the blade flange thoroughly before fit-

ting the new blade.

•

 Mount and fasten the new saw blade in rever-

se order.

•

 Caution! Note the running direction. The cut-

ting angle of the teeth must point in running 

direction, i.e. forwards (see the arrow on the 

blade guard).

•

 Refit and set the splitter (5), table insert (6) 

and the saw blade guard (2) (see 6.4, 6.3, 

6.5).

•

 Check to make sure that all safety devices 

are properly mounted and in good working 

condition before you begin working with the 

saw again.

•

 Warning! Every time that you change the saw 

blade, check that the saw blade guard (2) 

opens and closes again in accordance with 

requirements. Also check that the saw blade 

(4) spins freely in the saw blade guard (2).

•

 Warning! Every time that you change the saw 

blade (4), check to see that it spins freely in 

the table insert (6) in both perpendicular and 

45° angle settings.

•

 Warning! You should replace the table insert 

(6) immediately whenever it is worn or dama-

ged (see 6.3).

•

 Warning! The work to change and align the 

saw blade (4) must be carried out correctly.

Anl_TC_TS_315_U_SPK9-1.indb   32

Anl_TC_TS_315_U_SPK9-1.indb   32

23.03.2020   09:16:57

23.03.2020   09:16:57