Einhell TC-TS 315 - Инструкция по эксплуатации - Страница 33

GB

- 33 -

6.7  Connection for dust extractor

A connection for a dust extractor is provided on 

the extractor adapter (16) on the housing and on 

the saw blade guard (2).

6.7.1 Dust extraction using a vacuum extrac-

tion system

•

 The product is not supplied with a vacuum 

extraction system, which is available as ac-

cessory.

•

 Connect the suction hose of the vacuum ext-

raction system to the 100 mm diameter of the 

extractor adapter (16).

6.7.2 Dust extraction using a vacuum ext-

raction system and extractor adapter set 

(Fig. 22)

•

 The product is not supplied with an extractor 

adapter set with a suction hose and a vacuum 

extraction system, which are available as ac-

cessories.

•

 Connect the suction hose of the vacuum ext-

raction system to the 100 mm diameter of the 

extractor adapter (16).

•

 Using a crosstip screwdriver, undo the screw 

on the cap (51) on the saw blade guard (2).

•

 Remove the cap (51) from the saw blade gu-

ard (2).

•

 Remove the cap for the extractor adapter(50).

•

 Then connect the saw blade guard (2) and 

the side connection of the extractor adapter 

(16) to the suction hose.

6.7.3 Recommended requirements to be met 

by the vacuum extraction system

To ensure that dust and chips are satisfactorily 

carried away from the point at which they are 

generated to the vacuum extraction system, the 

vacuum extraction system which is used needs to 

meet the following requirements:

•

 Connection facility as described in 6.7.1 or 

6.7.2

•

 Required air flow: 850 m3/h

•

 Underpressure at the extractor adapter: maxi-

mum 1500 Pa

•

 Recommended air speed in the hose: 20 m/s

6.8  Fitting the accessory slide (Figs. 24, 26)

•

 The slide is available from retail stores

as a special accessory for the TC-TS 315

model – it is not included in the scope of

this delivery.

•

 Remove the guide rail (41) for the cross stop 

and remove the screws (32), washers (35), 

spring washers (36) and nuts (38).

•

 Fit the slide plate (100) and stop rail (101) to-

gether. To do so, use the large hexagon screw 

(107) and medium washer (116) at the pivot 

point. In addition, fasten the clamping lever 

(106) using two large washers (108) and the 

self-locking nut (109). Important! The clam-

ping lever (106) must be mounted in such 

a way that the stop can be moved when the 

clamping lever is released and is locked when 

the clamping lever is secured. Adjust the 

clamping force with the self-locking nut (109).

•

 Fit the two angles (103, 104) to the guide 

rail (102) using the washers (113), spring 

washers (114) and hexagon screws (112). 

•

 Then fasten the angles (103, 104) together 

with the guide rail (102) to the left legs (29) on 

the bench-type circular saw. To do this, use 

one hexagon screw (112), two washers (113), 

one spring washer (114) and one nut (115) at 

each point.

•

 Place the slide plate (100) together with the 

stop rail (101) onto the guide rail (102) from 

the front.

•

 If there is any slackness between the guide 

rail and the running bearings of the slide pla-

te, then the two lower bearings must be ad-

justed using the screw (A) and the eccentric 

screw (B), so that the slide can glide freely.

•

 Fit the socket head screws (110) to the front 

and rear of the guide rail (102) together with 

the locking grip (111); they serve as a limit 

stop.

•

 The stop rail (101) must move parallel to the 

saw table at a distance of approx. 1 mm. Sla-

cken the screws for the angles (103, 104) to 

do this. Then adjust adjust the rail in such a 

way that there is a 1 mm gap between the rail 

and the saw table in every position.

•

 Please note that for technical reasons relating 

to delivery, some loose screws/washers may 

be left over even if the slide is assembled and 

fitted correctly (special accessory), because, 

e.g. they may already be provided on the 

bench-type circular saw.

7. Operation

Switch on an extraction system prior to star-

ting with the work.

7.1 On/O

ff

  switch (Fig. 1/Item 11)

•

To turn the saw on, press the green button 

„I“. Wait for the blade to reach its maximum 

Anl_TC_TS_315_U_SPK9-1.indb   33

Anl_TC_TS_315_U_SPK9-1.indb   33

23.03.2020   09:16:57

23.03.2020   09:16:57