Ryobi R18CS-0 - Инструкция по эксплуатации - Страница 3

English

1

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

EL

TR

Safety, performance, and dependability have been given 
top priority in the design of your cordless circular saw.

INTENDED USE

The product is intended for cutting all types of wood.
Do not use the product in any way other than those stated 
for intended use.

 WARNING

Read all safety warnings and all instructions.

 Failure 

to follow the warnings and instructions may result in 

HOHFWULFVKRFN¿UHDQGRUVHULRXVLQMXU\

Save all warnings and instructions for future reference.

CIRCULAR SAW SAFETY WARNINGS

CUTTING PROCEDURES

Ŷ

DANGER: Keep hands away from cutting 
area and the blade. Keep your second hand 
on auxiliary handle, or motor housing. 

If both 

hands are holding the saw, they cannot be cut by the 
blade.

Ŷ

Do not reach underneath the workpiece.

 The guard 

cannot protect you from the blade below the workpiece.

Ŷ

Adjust the cutting depth to the thickness of the 
workpiece.

 Less than a full tooth of the blade teeth 

should be visible below the workpiece.

Ŷ

Never hold piece being cut in your hands or across 
your leg. Secure the workpiece to a stable platform.

It is important to support the work properly to minimize 
body exposure, blade binding, or loss of control.

Ŷ

Hold power tool by insulated gripping surfaces only 
when performing an operation where the cutting 
tool may contact hidden wiring.

 Contact with a “live” 

wire will also make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

Ŷ

When ripping, always use a rip fence or straight 
edge guide.

 This improves the accuracy of cut and 

reduces the chance of blade binding.

Ŷ

Always use blades with correct size and shape 
(diamond versus round) of arbour holes.

 Blades that 

do not match the mounting hardware of the saw will run 
eccentrically, causing loss of control.

Ŷ

Never use damaged or incorrect blade washers 
or bolt.

 The blade washers and bolt were specially 

designed for your saw, for optimum performance and 
safety of operation.

KICKBACK CAUSES AND RELATED WARNINGS:

Ŷ

Kickback is a sudden reaction to a pinched, bound or 
misaligned saw blade, causing an uncontrolled saw to 
lift up and out of the workpiece toward the operator;

Ŷ

When the blade is pinched or bound tightly by the kerf 
closing down, the blade stalls and the motor reaction 

drives the unit rapidly back toward the operator;

Ŷ

If the blade becomes twisted or misaligned in the cut, 
the teeth at the back edge of the blade can dig into the 
top surface of the wood causing the blade to climb out 

RIWKHNHUIDQGMXPSEDFNWRZDUGWKHRSHUDWRU

.LFNEDFN LV WKH UHVXOW RI VDZ PLVXVH DQGRU LQFRUUHFW

operating procedures or conditions and can be avoided by 
taking proper precautions as given below.

Ŷ

Maintain a firm grip with both hands on the saw 
and position your arms to resist kickback forces. 
Position your body to either side of the blade, but 
not in line with the blade.

 Kickback could cause the 

VDZ WR MXPS EDFNZDUGV EXW NLFNEDFN IRUFHV FDQ EH

controlled by the operator, if proper precautions are 
taken.

Ŷ

When blade is binding, or when interrupting a cut 
for any reason, release the trigger and hold the saw 
motionless in the material until the blade comes 
to a complete stop. Never attempt to remove the 
saw from the workpiece or pull the saw backward 
while the blade is in motion or kickback may occur.

Investigate and take corrective actions to eliminate the 
cause of blade binding.

Ŷ

When restarting a saw in the workpiece, centre the 
saw blade in the kerf and check that saw teeth are 
not engaged into the material.

 If saw blade is binding, 

it may walk up or kickback from the workpiece as the 
saw is restarted.

Ŷ

Support large panels to minimise the risk of blade 
pinching and kickback.

 Large panels tend to sag 

under their own weight. Supports must be placed under 
the panel on both sides, near the line of cut and near 
the edge of the panel.

Ŷ

Do not use dull or damaged blades.

 Unsharpened 

or improperly set blades produce narrow kerf causing 
excessive friction, blade binding and kickback.

Ŷ

Blade depth and bevel adjusting locking levers 
must be tight and secure before making cut.

 If blade 

DGMXVWPHQW VKLIWV ZKLOH FXWWLQJ LW PD\ FDXVH ELQGLQJ

and kickback.

Ŷ

Use extra caution when sawing into existing walls 
or other blind areas.

 The protruding blade may cut 

REMHFWVWKDWFDQFDXVHNLFNEDFN

LOWER GUARD FUNCTION

Ŷ

Check lower guard for proper closing before each 
use. Do not operate the saw if lower guard does not 
move freely and close instantly. Never clamp or 
tie the lower guard into the open position.

 If saw is 

accidentally dropped, lower guard may be bent. Raise 
the lower guard with the retracting handle and make 
sure it moves freely and does not touch the blade or any 
other part, in all angles and depths of cut.

Ŷ

Check the operation of the lower guard spring. If 
the guard and the spring are not operating properly, 
they must be serviced before use.

 Lower guard may 

operate sluggishly due to damaged parts, gummy 
deposits, or a build-up of debris.