Makita HS011GZ - Инструкция по эксплуатации - Страница 15

15 ENGLISH

Overdischarge protection

When the battery capacity becomes low, the tool stops 

automatically. If the product does not operate even 

when the switches are operated, remove the batteries 

from the tool and charge the batteries.

Protections against other causes

Protection system is also designed for other causes 

that could damage the tool and allows the tool to stop 

automatically. Take all the following steps to clear the 

causes, when the tool has been brought to a temporary 

halt or stop in operation.

1.  Turn the tool off, and then turn it on again to 

restart.

2.  Charge the battery(ies) or replace it/them with 

recharged battery(ies).

3.  Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection 

system, then contact your local Makita Service Center.

Indicating the remaining battery 

capacity

Press the check button on the battery cartridge to indi

-

cate the remaining battery capacity. The indicator lamps 

light up for a few seconds.

► 

Fig.8:

1.

 Indicator lamps 

2.

 Check button

Indicator lamps

Remaining 

capacity

Lighted

Off

Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the 

battery.

The battery 

may have

malfunctioned.

NOTE:

 Depending on the conditions of use and the 

ambient temperature, the indication may differ slightly 

from the actual capacity.

NOTE:

 The first (far left) indicator lamp will blink when 

the battery protection system works.

Switch action

WARNING:

Before installing the battery car-

tridge into the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released.

WARNING:

NEVER defeat the lock-off button 

by taping down or some other means.

 A switch with 

a negated lock-off button may result in unintentional 

operation and serious personal injury.

WARNING:

NEVER use the tool if it runs when 

you simply pull the switch trigger without press-

ing the lock-off button.

 A switch in need of repair 

may result in unintentional operation and serious 

personal injury. Return tool to a Makita service center 

for proper repairs BEFORE further usage.

To prevent the switch trigger from being accidentally 

pulled, a lock-off button is provided. To start the tool, 

depress the lock-off button and pull the switch trigger. 

Release the switch trigger to stop.

► 

Fig.9:

1.

 Switch trigger 

2.

 Lock-off button

NOTICE:

Do not pull the switch trigger hard 

without pressing in the lock-off button.

 This can 

cause switch breakage.

CAUTION:

The tool starts to brake the cir-

cular saw blade rotation immediately after you 

release the switch trigger. Hold the tool firmly to 

respond the reaction of the brake when releasing 

the switch trigger.

 Sudden reaction can drop the tool 

off your hand and can cause a personal injury.

Adjusting depth of cut

CAUTION:

After adjusting the depth of cut, 

always tighten the lever securely.

Loosen the lever on the depth guide and move the base 

up or down. At the desired depth of cut, secure the base 

by tightening the lever.

For cleaner, safer cuts, set cut depth so that no more 

than one blade tooth projects below workpiece. Using 

proper cut depth helps to reduce potential for danger-

ous KICKBACKS which can cause personal injury.

► 

Fig.10:

1.

 Lever

NOTICE:

 If the base doesn't slide up or down 

smoothly, the depth guide may have been tilted. In 

this case, adjust the depth guide (refer the section 

about adjusting the depth guide).

Bevel cutting

CAUTION:

After adjusting the bevel angle, 

always tighten the clamping screws securely.

Loosen the clamping screws. Set for the desired angle 

by tilting accordingly, then tighten the clamping screws 

securely.

► 

Fig.11:

1.

 Clamping screw