Makita DHS680Z - Инструкция по эксплуатации - Страница 5

5 

• 

Be sure to identify safety measures to protect the 
operator that are based on an estimation of 
exposure in the actual conditions of use (taking 
account of all parts of the operating cycle such as 
the times when the tool is switched off and when it 
is running idle in addition to the trigger time). 
 

ENH101-18 

For European countries only 

EC Declaration of Conformity 

Makita declares that the following Machine(s): 

Designation of Machine:   
Cordless Circular Saw 
Model No./ Type: DHS680 

Conforms to the following European Directives: 

2006/42/EC 

They are manufactured in accordance with the following 
standard or standardized documents: 

EN60745 

The technical file in accordance with 2006/42/EC is 
available from: 

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium 
 

18.3.2014 

000331 

Yasushi Fukaya 

Director 

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium 

GEA010-1 

General Power Tool Safety 
Warnings 

WARNING Read all safety warnings and all 

instructions.

 Failure to follow the warnings and 

instructions may result in electric shock, fire and/or 
serious injury. 

Save all warnings and instructions for 
future reference. 

GEB060-8 

CORDLESS CIRCULAR SAW 
SAFETY WARNINGS 

Cutting procedures 

1. 

DANGER: Keep hands away from cutting 

area and the blade. Keep your second hand 
on auxiliary handle, or motor housing.

 If both 

hands are holding the saw, they cannot be cut by 
the blade. 

2. 

Do not reach underneath the workpiece.

 The 

guard cannot protect you from the blade below 
the workpiece. 

3. 

Adjust the cutting depth to the thickness of 
the workpiece.

 Less than a full tooth of the blade 

teeth should be visible below the workpiece. 

4. 

Never hold piece being cut in your hands or 
across your leg. Secure the workpiece to a 
stable platform.

 It is important to support the 

work properly to minimize body exposure, blade 
binding, or loss of control. 

A typical illustration of proper hand support 
and workpiece support.

000161 

5. 

Hold the power tool by insulated gripping 
surfaces only, when performing an operation 
where the cutting tool may contact hidden 
wiring.

 Contact with a "live" wire will also make 

exposed metal parts of the power tool "live" and 
could give the operator an electric shock. 

6. 

When ripping, always use a rip fence or 
straight edge guide.

 This improves the accuracy 

of cut and reduces the chance of blade binding. 

7. 

Always use blades with correct size and 
shape (diamond versus round) of arbour 
holes.

 Blades that do not match the mounting 

hardware of the saw will run eccentrically, 
causing loss of control. 

8. 

Never use damaged or incorrect blade 
washers or bolt.

 The blade washers and bolt 

were specially designed for your saw, for 
optimum performance and safety of operation. 

Kickback causes and related warnings 

−

  kickback is a sudden reaction to a pinched, bound 

or misaligned saw blade, causing an uncontrolled 
saw to lift up and out of the workpiece toward the 
operator; 

−

  when the blade is pinched or bound tightly by the 

kerf closing down, the blade stalls and the motor 
reaction drives the unit rapidly back toward the 
operator; 

−

  if the blade becomes twisted or misaligned in the 

cut, the teeth at the back edge of the blade can dig 
into the top surface of the wood causing the blade 
to climb out of the kerf and jump back toward the 
operator. 

Kickback is the result of saw misuse and/or incorrect 
operating procedures or conditions and can be avoided 
by taking proper precautions as given below.