Makita 2712 - Инструкция по эксплуатации - Страница 8

Пилы дисковые Makita 2712 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 72
Загружаем инструкцию
background image

8

Save all warnings and 

instructions for future reference.

ADDITIONAL SAFETY RULES 

FOR TOOL

ENB122-1

SAVE THESE INSTRUCTIONS. 

1.

Wear eye protection. 

2.

Do not use the tool in presence of flammable 
liquids or gases. 

3.

NEVER use the tool with an abrasive cut-off wheel 
installed. 

4.

Check the blade carefully for cracks or damage 
before operation. Replace cracked or damaged 
blade immediately. 

5.

Use only saw blades recommended by the 
manufacturer and which conform to EN847-1, and 
observe that the riving knife must not be thicker 
than the width of the cut by the saw blade and not 
thinner than the body of the blade. 

6.

Always use accessories recommended in this 
manual. Use of improper accessories such as 
abrasive cut-off wheels may cause an injury. 

7.

Select the correct saw blade for the material to be 
cut. 

8.

Do not use saw blades manufactured from high 
speed steel. 

9.

To reduce the emitted noise, always be sure that 
the blade is sharp and clean. 

10.

Use correctly sharpened saw blades. Observe the 
maximum speed marked on the saw blade. 

11.

Clean the spindle, flanges (especially the 
installing surface) and hex nut before installing 
the blade. Poor installation may cause vibration/
wobbling or slippage of the blade. 

12.

Use saw-blade guard and riving knife for every 
operation for which it can be used, including all 
through sawing operations. Always install the 
blade guard following the instructions out-lined in 
this manual. Through sawing operations are those 
in which the blade cuts completely through the 
workpiece as in ripping or cross cutting. NEVER 
use the tool with a faulty blade guard or secure the 
blade guard with a rope, string, etc. Any irregular 
operation of the blade guard should be corrected 
immediately. 

13.

Immediately reattach the guard and riving knife 
after completing an operation which requires 
removal of the guard. 

14.

Do not cut metal objects such as nails and screws. 
Inspect for and remove all nails, screws and other 
foreign material from the workpiece before 
operation. 

15.

Remove wrenches, cut-off pieces, etc. from the 
table before the switch is turned on. 

16.

NEVER wear gloves during operation. 

17.

Keep hands out of the line of the saw blade. 

18.

NEVER stand or permit anyone else to stand in 
line with the path of the saw blade. 

19.

Make sure the blade is not contacting the riving 
knife or workpiece before the switch is turned on. 

20.

Before using the tool on an actual workpiece, let it 
run for a while. Watch for vibration or wobbling 
that could indicate poor installation or a poorly 
balanced blade. 

21.

The tool should not be used for slotting, rabbeting 
or grooving.

22.

Replace table insert when worn. 

23.

NEVER make any adjustments while tool is 
running. Disconnect tool before making any 
adjustments. 

24.

Use a push stick when required. Push sticks 
MUST be used for ripping narrow workpieces to 
keep your hands and fingers well away from the 
blade. 

25.

Always store the push-stick when it is not in use. 

26.

Pay particular attention to instructions for 
reducing risk of KICKBACK. KICKBACK is a 
sudden reaction to a pinched, bound or 
misaligned saw blade. KICKBACK causes the 
ejection of the workpiece from the tool back 
towards the operator. KICKBACKS CAN LEAD TO 
SERIOUS PERSONAL INJURY. Avoid KICKBACKS 
by keeping the blade sharp, by keeping the rip 
fence parallel to the blade, by keeping the riving 
knife and blade guard in place and operating 
properly, by not releasing the workpiece until you 
have pushed it all the way past the blade, and by 
not ripping a workpiece that is twisted or warped 
or does not have a straight edge to guide along 
the fence. 

27.

Do not perform any operation freehand. Freehand 
means using your hands to support or guide the 
workpiece, in lieu of a rip fence or miter gauge. 

28.

NEVER reach around or over saw blade. NEVER 
reach for a workpiece until the saw blade has 
completely stopped. 

29.

Avoid abrupt, fast feeding. Feed as slowly as 
possible when cutting hard workpieces. Do not 
bend or twist workpiece while feeding. If you stall 
or jam the blade in the workpiece, turn the tool off 
immediately. Unplug the tool. Then clear the jam. 

30.

NEVER remove cut-off pieces near the blade or 
touch the blade guard while the blade is running. 

31.

Knock out any loose knots from workpiece 
BEFORE beginning to cut. 

32.

Do not abuse cord. Never yank cord to disconnect 
it from the receptacle. Keep cord away from heat, 
oil, water and sharp edges. 

33.

Some dust created from operation contains 
chemicals known to cause cancer, birth defects or 
other reproductive harm. Some examples of these 
chemicals are: 

-

lead from lead-based-painted material and, 

-

arsenic and chromium from chemically-treated 
lumber. 

-

Your risk from these exposures varies, 
depending on how often you do this type of 
work. To reduce your exposure to these 
chemicals: work in a well ventilated area and 
work with approved safety equipment, such as 
those dust masks that are specially designed to 
filter out microscopic particles. 

34.

When using the tool indoors, always connect the 
tool to an external dust extraction system. 

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к Makita 2712?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"