Energy 58G008 - Инструкция по эксплуатации - Страница 14

14

• When the cutting blade jams or stops cutting due to any 

reason, release the switch button and hold the saw still in the 
material until the blade or disc stops completely. 

• Never attempt to remove the cutting blade from material 

being cut nor pull the saw back when the blade is rotating. It 
may cause kick back. 

Investigate and implement correction actions 

to eliminate causes of cutting blade seizing.

• When restarting the saw in the processed material, centre 

the cutting blade in the kerf and ensure the blade teeth are 
not blocked in the material. 

When the cutting blade jams during 

restart, it may slide off or cause kick back against the processed 
material.

• Support large boards to minimize risk of pinching and kick 

back of the circular saw. 

Large boards tend to bend under own 

weight. Place supports under board on both sides, close to the cutting 
line and close to the board edge.

• Do not use blunt or damaged cutting blades. 

Blunt or incorrectly 

positioned blade teeth create narrow kerf, excessive friction, jamming 
of cutting blade and kick back.

• Firmly set clamps for cutting depth and bevel angle before 

making a cut. 

Change of saw settings during cutting may cause 

jamming and kick back.

• Be very careful during plunge cutting in division walls. 

Cutting 

blade may encounter objects not visible from the outside and cause 
kick back.

FEATURES OF LOWER PROTECTIVE GUARD

• Make sure the lower guard is appropriately positioned before 

each use. Do not use the saw when the lower guard does not 
move freely and does not close immediately. Do not fix and 
do not leave the lower guard open. 

When the saw is accidentally 

dropped the lower guard may get deformed. Lift the lower guard 
with pull-handle and ensure it is free to move and does not touch the 
blade nor any other part of the tool for any setting of cutting depth 
and angle.

• Check functioning of the lower guard spring. Repair the guard 

and its spring before use when they do not work properly. 

Lower guard may be malfunctioning and slowed down due to 
damaged parts, sticky sediments or building up of layers of wastes.

• Manual pulling off the lower guard is allowed only when 

special cutting is performed, such as “plunge cutting” and 
“compound cutting”. Lift the lower guard with its pull handle. 
As soon as the cutting blade sinks in the material the guard 
must be released.

 For all other cuts it is recommended that the 

lower guard works automatically.

• Always make sure the lower guard covers cutting blade before 

putting the circular saw away on the workbench or floor. 

Uncovered, rotating blade will move the circular saw back and will 
cut everything in its way. Consider time required for stopping the 
blade after the saw is switched off.

ADDITIONAL SAFETY INSTRUCTIONS

•

Do not use damaged or deformed cutting blades.

•

Do not use grinding wheels.

•

Use only cutting blades that are recommended by the 
manufacturer and comply with the standard EN 847-1.

•

Do not use cutting blades without sintered carbide tips on teeth.

• Dust of certain wood types may be dangerous to health. 

Direct 

physical contact with dusts may cause allergic reaction and/or 
respiratory system diseases of operator or bystanders. Dusts of oak 
and beech are considered carcinogenic, especially in connection 
with wood processing substances (wood impregnants).

•

Use personal protection measures, such as:

-

earmuff protectors to reduce risk of hearing damage,

-

eye shield,

-

respiratory system protection to reduce risk of harmful dusts 
inhalation,

-

gloves for maintenance of cutting blades and other rough and 
sharp materials (hold cutting blades by mount hole whenever 
possible).

•

Connect dust extraction system when cutting wood.

•

Match cutting blade with material that you plan to cut.

•

Never use the saw for cutting materials other than wood and 
wood-like.

•

Do not use the saw without guard or when the guard is blocked.

•

Floor close to the machine work place must be kept tidy and 
without loose materials and protrusions.

•

Provide appropriate work place illumination.

•

Machine operator must be properly trained for use, operation and 
working with the machine.

•

Observe maximum speed indicated on the cutting blade.

•

Make sure to use parts in accordance with the manufacturer’s 
instructions.

•

If the saw is equipped with laser, replacement with laser of another 
type is forbidden and all repairs must be carried out by the service.

•

Do not use the tool stationary. It is not designed for use with 
sawing table.

CORRECT OPERATION AND USE OF BAT TERIES

•

Batter y charging process should be super vised by the user. 

•

Avoid charging the batter y in temperature lower than 0°C. 

• Use only the charger recommended by the manufacturer. 

Using charger designed for other type of batter y brings the risk 
of fire.

• When the battery is not in use, store it away from metal 

objects such as paper clips, coins, keys, nails, screws or any 
other small metal objects that can shor t-circuit the battery 
connectors. 

Shor t- circuit of batter y connectors may cause burns 

or fire.

• In case of battery damage and/or improper use it may 

produce gas. Ventilate room and seek medical attention in 
case of medical symptoms. 

Gas can damage respirator y tract.

• In extreme conditions liquid may leak out of the battery. 

The liquid coming out of the battery may cause irritations 
or burns.

 When a leak is found, follow the below procedure:

-

Carefully wipe the liquid with a cloth. Avoid contact of the liquid 
with skin and eyes.

-

In case the liquid gets onto skin, immediately wash the spot 
abundantly with clean water, you can also neutralize the liquid 
with a mild acid, e.g. lemon juice or vinegar. 

-

 When the liquid gets into eyes, wash it immediately with a lot of 
clean water for at least 10 minutes. Seek medical advice.

• Do not use damaged or modified battery. 

Damaged or 

modified batteries may behave unpredictably, causing fire, 
explosion or risk of injuries.

• Do not expose the battery to humidity or water.

•

Always keep the batter y away from sources of heat. Do not 
leave the batter y for a long time in high temperature (in 
direct sunlight, in proximity of heaters and wherever the 
temperature exceeds 50°C).

• Do not expose the battery to fire or excessive temperature. 

Exposure to fire or temperature above 130°C may cause explosion.

CAUTION!

 Temperature of 130°C can be also defined as 265°F.

• Observe all charging instructions. Do not charge the battery 

in temperature outside of range defined in the rating data 
table from the instruction manual. 

Incorrect charging or 

charging in temperature outside of defined range may damage the 
battery and increase the risk of fire.