Energy 58G008 - Инструкция по эксплуатации - Страница 13

13

GWARANCJA I SERWIS

Warunki gwarancji oraz opis postepowania w prz ypadku 

reklamacji zawar te są w załączonej Karcie Gwarancyjnej.

Ser wis Centralny
GT X Ser vice   

tel. +48 22 573 03 85

Ul. Pograniczna 2/4 

fax. +48 22 573 03 83

02-285 Warszawa 

e -mail  graphite@gtxser vice.pl

Sieć Punktów Ser wisowych do napraw gwarancyjnych 
i pogwarancyjnych dostępna na platformie internetowej 

gtxservice.pl

GRAPHITE zapewnia dostępność części zamiennych oraz 
materiałów eksploatacyjnych dla urządzeń i elektronarzędzi. 
Pełna ofer ta części i usług na 

gtxservice.pl

.

Zeskanuj QR kod i wejdź na 

gtxservice.pl

TRANSLATION OF  

THE ORIGINAL INSTRUCTIONS

CO R D L E S S  C I R C U L A R  S AW 

58G008

CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL 
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.

DETAILED SAFETY REGULATIONS

DETAILED SAFETY REGULATIONS FOR SAFE OPERATION WITH 
CIRCULAR SAW WITHOUT SPLITTING WEDGE

Caution: 

Remove the battery powering the device before any adjustments, 
maintenance (replacement of cutting blade) or repair.

• Keep your hands away from cutting area and cutting blade. 

Keep the second hand on the secondary handle or the 
motor casing. 

When holding the saw with both hands the risk 

of injur y with cutting blade is reduced.

• Do not reach under the processed material. 

Guard does not 

protect from rotating cutting blade below processed material.

• Adjust cutting depth to thickness of processed material.

It is recommended that the cutting blade reaches below the 
processed material no more than tooth-length.

• Never hold processed material in hands, never keep it on 

legs. Fix processed material to sound base. 

Good fixing of 

processed material is impor tant to avoid danger of contact with 
body, rotating cutting blade being caught or loss of control over 
the operation.

• Hold the insulated sur faces of the saw that are designed 

for such purpose whenever the rotating cutting blade can 
encounter live wires. 

Contact of device metal par ts with live 

wire may cause operator ’s electric shock.

• When ripping always use guide for ripping or edge guide. 

It improves cutting accuracy and reduces risk of pinching the 
rotating cutting blade in material.

• Use only cutting blades with correct arbour hole diameter. 

Cutting blades that do not match seating may operate with 
eccentric offset, which causes loss of control over operation.

• Never use damaged or incorrect washers or bolts to install 

cutting blade. 

Washers and fixing bolts for cutting blade 

installation were designed especially for circular saw to provide 
optimal operation and safety of use.

KICK BACK, CAUSES AND WAYS TO REDUCE IT

•

Kick back is a sudden lift and moving the saw back in the cutting 
line towards operator. This is caused by uncontrolled cutting with 
cutting blade being caught, pinched or incorrectly guided.

•

When the cutting blade is caught or pinched in material, the blade 
stops and motor reaction produces sudden movement of the saw 
to the back, towards operator.

•

If the saw is unaligned or positioned incorrectly in the object 
being cut, blade teeth may hit the upper surface of the material 
when leaving the material. It will cause sudden raise of the saw, 
and kick back towards operator.

CAUTION! 

Kick back is an effect of improper use of circular saw, or 

wrong operating procedures or conditions, and can be avoided by 
observing applicable, below-mentioned precautions:

• Hold the circular saw firmly with both hands in position that 

allows to resist kick-back. Stand to the side of the circular saw 
but not in the line of cutting. 

Kick back may cause sudden move 

of circular saw to the back, but its force can be controlled by operator 
when appropriate precaution measures are taken.