Einhell TE-CS 18/165-1 Li (4331207) - Инструкция по эксплуатации - Страница 21

GB

- 21 -

6.2 Using the circular saw

• 

 Adjust the cutting depth, cutting angle and 

parallel stop (see section 5.1, 5.2 and 5.4)

• 

 Do not switch on the circular saw until you 

have fitted a saw blade.

• 

 Place the saw foot flat on the workpiece you 

wish to saw. The saw blade must not be in 

contact with the workpiece.

• 

 Hold the circular saw firmly with both hands.

6.3 Switching ON/OFF (Fig. 12)

To switch on:

Press the locking button (3) and the ON/OFF 

switch (2) at the same time

• 

 Allow the saw blade to accelerate until it 

reaches full speed. Then slowly move the saw 

blade along the cutting line. Only exert gentle 

pressure on the saw blade as you do so.

To switch o

ff

 :

Release the locking button and ON/OFF switch

• 

 If you release the handle the equipment will 

shut down automatically which means that it 

cannot operate accidentally.

• 

 Ensure that you do not cover or block the ven-

tilation openings whilst working with the tool.

• 

 Do not slow down the saw blade after you 

switch it off by pressing it sideways.

• 

 Important! Do not put down the machine until 

the saw blade has reached a complete stand-

still.

Important. Carry out a trial cut in a piece of 

waste wood

6.4 Changing the saw blade (Fig. 13-16)

Warning!

Always remove the battery pack before making 

adjustments to the equipment.

Use only saw blades which comply with standard 

EN 847-1 and are of the same type as the saw 

blade supplied with this circular saw. Ask your 

dealer for advice.

Warning!

Do not use grinding wheels!

The diameters of the saw blades used must cor-

respond to the diameters speci

fi

 ed on the hand-

held circular saw blade!

Use only recommended saw blades!

Use the saw blade key (13) supplied to change 

the saw blade. The saw blade key (13) is stored 

in the housing. If required, pull the saw blade key 

(13) out of the housing (see Figure 13).

Important. The hand-held circular saw must not 

be operated with the saw blade key (13) inserted 

in it.

• 

 Press the spindle lock (11).

• 

 Undo the screw to secure the saw blade (17) 

using the saw blade key (13).

• 

Push back and secure the moving swing 

guard hood (19) using the lever for the swing 

guard hood (20).

• 

 Remove the flange (18) and the saw blade 

(12) in a downwards direction.

• 

 Clean the flange and insert the new saw bla-

de. Pay attention to the running direction (see 

arrow on the guard hood and saw blade).

• 

 Tighten the screw to secure the saw blade 

(17), check it runs true.

• 

 Before you press the On/Off switch, make 

sure that the saw blade is correctly fitted and 

that moving parts run smoothly and the clam-

ping screws are tightened securely.

6.5 LED lamp (Fig. 1/Item 5)

The LED lamp (5) can be used in poor lighting 

conditions to additionally illuminate the cutting 

position. The LED lamp (5) will come on automa-

tically as soon as you press the locking button for 

the On/O

ff

  switch (3).

7.  Cleaning, maintenance and 

ordering of spare parts

Danger!

Always pull out the battery pack before starting 

any cleaning work.

7.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

Anl_TE_CS_18_165-1_Li_Solo_SPK13.indb   21

Anl_TE_CS_18_165-1_Li_Solo_SPK13.indb   21

12.05.2022   15:07:57

12.05.2022   15:07:57