Einhell TE-CS 18/165-1 Li (4331207) - Инструкция по эксплуатации - Страница 20

GB

- 20 -

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long 

service, you should take care to recharge it 

promptly. You must recharge the battery pack 

when you notice that the performance of the 

device drops. Never allow the battery pack to 

become fully discharged. This will cause it to 

develop a defect.

Dans l‘intérêt d‘une longue durée de fonctionne-

ment du bloc accumulateur, vous devez prendre 

soin de recharger le bloc accumulateur en temps 

voulu. Ceci est dans tous les cas indispensable 

lorsque vous constatez une diminution de la 

puissance de l‘appareil. Ne déchargez jamais 

complètement le bloc accumulateur. Ceci cause 

l‘endommagement du bloc accumulateur !

5.7 Battery capacity indicator 

(Fig. 10 – Item h)

Press the battery capacity indicator switch (i). The 

battery capacity indicator (h) shows the charge 

status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED 

fl

 ashes:

The battery is empty, recharge the battery.

All LEDs blink:

The battery temperature is too low. Remove the 

battery from the equipment, keep it at room tem-

perature for one day. If the fault reoccurs, this me-

ans that the rechargeable battery has undergone 

exhaustive discharge and is defective. Remove 

the battery from the equipment. Never use or 

charge a defective battery.

6. Operation

Warning!

Always remove the battery pack before making 

adjustments to the equipment.

6.1 Working with the hand-held circular saw

• 

 Always hold the tool firmly by the handles 

provided (1 and 10) to ensure that you handle 

it safely when using it.

• 

 The swing guard hood (19) is pushed back 

automatically by the workpiece.

• 

 Do not use force!

• 

Push forwards gently and evenly with the 

circular saw.

• 

 The waste piece should be on the right-hand 

side of the circular saw so that the wide 

section of the support bench supports its full 

area.

• 

 If you are sawing down a line that has been 

drawn, guide the circular saw along the corre-

sponding notch.

• 

 Clamp small pieces of wood securely before 

sawing them. Never hold them with your 

hand.

• 

 Always follow the safety instructions. Wear 

safety goggles.

• 

 Do not use defective saw blades or blades 

that are cracked or broken.

• 

 Do not use any flanges / flange nuts whose 

bore hole is larger or smaller than those in the 

saw blade.

• 

 The saw blade must not be decelerated by 

hand or by applying lateral pressure to the 

blade.

• 

 Check that the swing guard hood works pro-

perly. The swing guard hood must not jam, 

and it must return to its initial position when 

you have completed the cut.

• 

 Before you use the circular saw, check the 

function of the swing guard hood with the 

mains plug disconnected.

• 

 Before you use the machine, ensure that the 

safety equipment such as the swing guard 

hood, flanges and adjustment devices are in 

working order and are correctly adjusted and 

secure.

• 

 You can connect a suitable dust extraction 

system to the sawdust extraction connector 

(14). Ensure that the dust extractor line is sa-

fely and correctly connected.

• 

 The moving swing guard hood must not be 

fixed in the retracted guard hood when the 

saw is in use.

Anl_TE_CS_18_165-1_Li_Solo_SPK13.indb   20

Anl_TE_CS_18_165-1_Li_Solo_SPK13.indb   20

12.05.2022   15:07:56

12.05.2022   15:07:56