Einhell TE-CS 18/165-1 Li (4331207) - Инструкция по эксплуатации - Страница 19

GB

- 19 -

5.1 Setting the cutting depth (Figure 2/3)

• 

  Release the handle on the rear of the guard 

hood for adjusting the cutting depth (4).

• 

 Place the saw foot (6) flat on the surface of 

the workpiece you wish to saw. Raise the saw 

until the saw blade (12) is at the required cut-

ting depth (a).

• 

 Refasten the handle for adjusting the cutting 

depth (4). Check the handle is securely faste-

ned.

5.2 Miter stop (Figure 4/5)

• 

 The preset standard angle between the saw 

foot (6) and saw blade (12) is 90°. You can 

adjust this angle to carry out angled cuts.

• 

 Release the locking lever for miter setting (7) 

on the front of the saw foot. 

• 

 You can now adjust the cutting angle to 

around 45°. Keep an eye on the cutting angle 

scale (9) as you do so.

• 

 Refasten the locking lever for miter setting (7). 

Check the handle is securely fastened.

5.3 Extraction of dust and chips (Figure 6)

• 

 Connect a suitable vacuum cleaner to the 

provided chip extractor connector (14) of your 

circular saw (vacuum cleaner not included). 

This will provide excellent dust extraction on 

the workpiece. The benefits are that you will 

protect both the equipment and your own 

health. Your work area will also be cleaner 

and safer.

• 

 Dust created when working may be dange-

rous. Refer to the section entitled “Safety inst-

ructions”.

• 

 Important! The vacuum cleaner you use for 

the extraction work must be suitable for the 

workpiece material.

• 

 Check that all the parts are properly connec-

ted.

5.4 Parallel stop (Figure 7/8)

• 

 The parallel stop (16) enables you to saw par-

allel lines.

• 

 Loosen the locking screw for the parallel stop 

(8) on the saw foot (6).

• 

 To assemble, slide the parallel stop (16) into 

the guide (c) on the saw foot (6) (see Figure 

7)

• 

 Set the required spacing and then tighten the 

locking screw (8) again.

• 

 Using the parallel stop: Position the parallel 

stop (16) flat on the edge of the workpiece 

and start the cut.

Important! Carry out a trial cut in a piece of 

waste wood

5.5 Line guide (Fig. 9)

Using the line guide (15) you can carry out exact 

cuts following cutting lines marked on the work-

piece. 

Use the mark (d) for the 0° or 90°angle setting

and the mark (b) for the 45° angle setting.

For information on the angle setting see 5.2

Important! Carry out a trial cut in a piece of 

waste wood

 5.6 Charging the LI battery pack (Fig. 10-11)

1.  Remove the battery pack (g) from the handle, 

pressing the pushlock buttons (f) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(j) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger.

In section 10 “Charger indicator” you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

Important!

Only use the rechargeable battery and charger 

when dry and with an ambient temperature of 

10-40°C.

Store the rechargeable battery, cordless tool and 

charger in a dry place with an ambient tempera-

ture of: Rechargeable battery = 10-20°C

Cordless tool, charger = 10-40°C.

If the battery pack fails to become charged, ple-

ase check

• 

 whether there is voltage at the socket-outlet

• 

 whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please 

return

• 

 the  charger

• 

 the battery pack

to our Customer Service Department.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

Anl_TE_CS_18_165-1_Li_Solo_SPK13.indb   19

Anl_TE_CS_18_165-1_Li_Solo_SPK13.indb   19

12.05.2022   15:07:56

12.05.2022   15:07:56