Bosch GBH 2-26 DRE - Инструкция по эксплуатации - Страница 16

16

 | English 

1 609 92A 220 | (28.4.16)

Bosch Power Tools

accessories, keep the hands warm, organisation of work pat-
terns.

Assembly



Before any work on the machine itself, pull the mains
plug.

Auxiliary Handle



Operate your machine only with the auxiliary handle 
14.

Changing the position of the auxiliary handle 
(see figure A)

The auxiliary handle 

14

 can be set to any position for a secure 

and low-fatigue working posture.

– Turn the bottom part of the auxiliary handle 

14

 in counter-

clockwise direction and swivel the auxiliary handle 

14

 to 

the desired position. Then retighten the bottom part of the 
auxiliary handle 

14

 by turning in clockwise direction.

Pay attention that the clamping band of the auxiliary han-
dle is positioned in the groove on the housing as intended 
for.

Adjusting the Drilling Depth (see figure B)

The required drilling depth 

X

 can be set with the depth stop 

13

.

– Press the button for the depth stop adjustment 

12

 and in-

sert the depth stop into the auxiliary handle 

14

.

The knurled surface of the depth stop 

13

 must face down-

ward.

– Insert the SDS-plus drilling tool to the stop into the SDS-

plus tool holder 

3

. Otherwise, the movability of the SDS-

plus drilling tool can lead to incorrect adjustment of the 
drilling depth.

– Pull out the depth stop until the distance between the tip of

the drill bit and the tip of the depth stop corresponds with 
the desired drilling depth 

X

.

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus tools are re-
quired that are inserted in the SDS-plus drill chuck.

For drilling without impact in wood, metal, ceramic and plas-
tic as well as for screwdriving, tools without SDS-plus are 
used (e. g., drill bits with cylindrical shank). For these tools, a 
keyless chuck or a key type drill chuck are required.

GBH 2-26 DFR: The SDS-plus quick change chuck 

2

 can easi-

ly be replaced against the quick change keyless chuck 

1

 pro-

vided.

Changing the Key Type Drill Chuck 
(GBH 2-26 E/RE/DE/DRE)

To work with tools without SDS-plus (e. g., drills with cylindri-
cal shank), a suitable drill chuck must be mounted (key type 
drill chuck or keyless chuck, accessories).

Mounting the Key Type Drill Chuck (see figure C)

– Screw the SDS-plus adapter shank 

20

 into a key type drill 

chuck 

19

. Secure the key type drill chuck 

19

 with the se-

curing screw 

18

. 

Please observe that the securing 

screw has a left-hand thread.

Inserting the Key Type Drill Chuck (see figure C)

– Clean the shank end of the adapter shank and apply a light 

coat of grease.

– Insert the key type drill chuck with the adapter shank into 

the tool holder with a turning motion until it automatically 
locks.

– Check the locking effect by pulling the key type drill chuck.

Removing the Key Type Drill Chuck

– Push the locking sleeve 

5

 toward the rear and pull out the 

key type drill chuck 

19

.

Removing/Inserting the Quick Change Chuck 
(GBH 2-26 DFR)

Removing the Quick Change Chuck (see figure D)

– Pull the lock ring for the quick change chuck 

6

 toward the

rear, hold it in this position and pull off the SDS-plus quick
change chuck 

2

 or the quick change keyless chuck 

1

 to-

ward the front.

– After removing, protect the replacement chuck against 

contamination.

Inserting the Quick Change Chuck (see figure E)

– Before inserting, clean the quick change chuck and apply a 

light coat of grease to the shank end.

– Grasp the SDS-plus quick change chuck 

2

 or the quick 

change keyless chuck 

1

 completely with your hand. Slide 

the quick change chuck with a turning motion onto the drill 
chuck mounting 

21

 until a distinct latching noise is heard.

– The quick change chuck is automatically locked. Check the 

locking effect by pulling the quick change chuck.

Changing the Tool

The dust protection cap 

4

 largely prevents the entry of drilling 

dust into the tool holder during operation. When inserting the 
tool, take care that the dust protection cap 

4

 is not damaged.



A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by 
an after-sales service.

Inserting SDS-plus Drilling Tools (see figure F)

The SDS-plus drill chuck allows for simple and convenient 
changing of drilling tools without the use of additional tools.

– GBH 2-26 DFR: Insert the SDS-plus quick change chuck 

2

.

– Clean and lightly grease the shank end of the tool.
– Insert the tool in a twisting manner into the tool holder until 

it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus drilling tool can 
move freely. This causes a certain radial run-out at no-load, 
which has no effect on the accuracy of the drill hole, as the 
drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figure G)

– Push back the locking sleeve 

5

 and remove the tool.

OBJ_BUCH-279-008.book  Page 16  Thursday, April 28, 2016  10:57 AM