TESY CN 051 150 - Инструкция по эксплуатации - Страница 4

EN

4

Operation and Storage Manual of Panel Heater

When the set time has elapse, the appliance going to Comfort mode 

!  

Deactivation of „Eco„ mode 

- You can exit “Eco” mode 

  by pushing “On/Off ”  

 button for 1.5 

sec. Then the heater turns off. The display will continue showing the set 
temperature. Or press “Mode”  

 button to choose different mode.

Visualization on Display in “Eco” mode  settings 

:

-  Set temperature

The display shows “Eco” 

 in the top and the set temperature 

1.3. Sleep mode 

with On/Off option –  two hours after activation, the 

convector decreases the set temperature with -3°C under the set temperature 
in Comfort mode. User could set the time range for operating in Sleep mode 
then the appliance switches to Comfort mode. By default: 6 hours. 

Activation of  „Sleep mode„ 

Push the button “Mode”  

 for 3 sec and select “Sleep mode” 

  by 

pushing any of the buttons:  

 or 

, and confirm with “Mode” button 

. If you want you can set the clock time: select by pushing any of the 

buttons: 

 or 

, reach actual hour time. Confirm with “Mode”  button. The 

minute icon is flashing and by pushing any of the buttons: 

 or 

, reach 

actual minute time. Confirm with “Mode” button (range 00.00-24.00). When the 
set time has elapse, the appliance going to Comfort mode!

Deactivation of  “Sleep mode” 

User can exit “Sleep mode” 

 by pushing “On/Off ” 

 button for 1.5 

sec. Then the heater turns off. The display will continue showing the set 
temperature. Or press “Mode” button 

 to choose different mode.

Visualization on Display in “Sleep” mode  settings 

:

-  Set temperature

The display shows “Sleep” 

 in the top and the set temperature 

2.  Basic modes

“Heating” mode   

Start “Heating” mode   

When the panel heater is switched-off its digital display shows 

.

By pushing the ON/OFF 

 button for 1.5 sec the appliance goes into “Heating” 

mode 

 . Then the display indicates 

 mode. The set temperature is 

indicating in the right. If the room temperature is lower than the set one, the 
heater will switch automatically on, and a heating sign 

 will appear on the 

display.

The display shows 

  in the top and the set temperature

Deactivation of  “Heating” mode 

User can exit “Heating” mode by pushing “On/Off ” 

 button for 1.5 sec. Then 

the heater turns off. The display will be showing 

  OFF. 

Temperature adjustment

By pushing any of the buttons: 

 or 

 the user enters “Temperature 

adjustment” mode and the user can change the temperature settings in 
the desired direction. The new settings are saved and the heater goes 
automatically into “Heating” mode 

. If any of 

 or 

 buttons get 

pressed longer than 0.5 sec., the temperature settings will start automatically 
increase or decrease at a rate of 6 units per second. The range of available 
temperature settings is from 10 up to 30 degrees. 

Delay start function 

The delay start function allows the user to set the time at which the convector will 
switch on and start heating.

Push the “Mode” button 

 for 3 sec and select “Delay Start” 

 by pushing 

any of the buttons: 

 or 

 and confirm with “Mode” button   

, user 

can enter the time and temperature, when it will automatically go to “Heating” 
mode. Initially a setting of 12 hours is set by default and by pushing 

or 

 buttons user can change the time settings in the desired direction. 

After the hour of “delay start” mode is chosen, press “Mode” 

 button for 

confirmation. After that set the temperature at which the convector will start 
operating by pushing of any of buttons: 

 or 

 . Confirm with “Mode”  

button 

. If any of 

 or 

 buttons is held for more than 0.5 seconds, 

the time and temperature settings start automatically increase or decrease at a 
rate of 4 units per second. Confirm with “Mode” button 

 or don’t press any 

button for 3 seconds. 

If user enters time – 00, this mode will not be implemented. If the “Delay start” 
mode is already enabled and user selects the “Delay Start” mode again, it can 
be changed the remaining time in both possible directions. You can exit this 
mode by pushing the “On/Off ” 

  button. Then panel heater will go into 

“Heating” mode. The “Delay start” needs to be set from 0 to 96 hours.

Visualization on Display in “Delay start” settings 

:

The display shows “Delay start” in the top and the set temperature  

Anti-frost mode  

If the room temperature falls below 5°C and the panel heater is off, the heater 
will turn on automatically in order to prevent freezing of the area. Indication – 

 in left top corner   - only when work the anti-frost mode

Factory settings of the function is ON (switched On).

Activation and deactivation of Anti-frost mode 

- If the customer wants to change it – push “Mode”  button 

 for 3 sec and 

select “Anti-frost”  mode 

 by pushing any of the buttons: 

 or 

. 

Confirm with “Mode”  button  

and user can push 

 button to reach ‘’OFF”. 

Confirm with “Mode”  button 

.