Lavor Pro TUCSON 2017 LP 8.671.0004 - Инструкция по эксплуатации - Страница 20

          (if fitted) 

Machines equipped with Total Stop: 

-  When the machine is working, by releasing the 

gun lever, the motor stops automatically to 

prevent component wear during the pump by-

pass phase (motor in stand-by). 

 -  By pressing the gun lever the motor starts au-

tomatically. 

•

 WARNING:

 do not leave the stand-by mode 

active for more than 5 minutes. 

-  At the end of the operation, set the switch to 

“OFF”. 

          (if fitted)

Machines equipped with delayed, low-voltage 

Total Stop: 

-  When the machine is working, by releasing 

the gun lever, after approximately 15 seconds 

the motor stops automatically to prevent com-

ponent wear during the pump by-pass phase 

(motor in stand-by). 

-  By pressing the gun lever the motor starts au-

tomatically. 

•

 WARNING: 

do not leave the stand-by mode 

active for more than 5 minutes. 

-  At the end of the operation, set the switch to 

“OFF”. 

IMPORTANT: 

(pict.11). It is advisable to put 

on the safety of the pistol trigger whenever the 

machine is stopped, in order to avoid uninten-

tional starting.

- Any automatic start of the machine with-

out pressing the gun trigger is attribut-

able to air bubbles in the water or other 

similar phenomena which do not imply 

the existence of any defects in the ma-

chine. 

- Please check that the coupling of the high 

pressure hose with the appliance and the 

gun supplied as standard equipments made 

correctly, that is to say without any water 

leak.

>  PRESSURE REGULATOR
If the appliance is equipped with a pressure 

regulator:

- when the pressure is set to minimum the 

T.S.may not trigger. Therefore, do not allow the 

appliance to function in by-pass for more than 

1 minute.

- do not act on the gun lever too frequently (this 

may cause a malfunction).

> INSTALLATION

- 

(0) 

(pict.4) Check that the master switch is 

turned to “OFF” and that the water filter is fit-

ted into the pump’s inlet pipe (pict.5 pos. 

⑤

).

-  (pict.5 pos.

⑩

) Screw the snap connection into 

place by hand, without the aid of tools.

-  Connect the water supply hose to the snap 

connection. The hose must have an inside di-

ameter of at least 13 mm (1/2”).

-  (pict.6 pos. 

④

)

Connect the high pressure hose 

to the pump’s outlet pipe. Press the high pres-

sure hose coupling fully down and then screw 

into place by hand without the aid of tools.

-  (pict.7) Connect the high pressure hose to the 

gun.

-  Turn the water tap fully on. The water tempera-

ture absolutely must be below 40°C.

IMPORTANTE:

 The washer machine has to 

operate with clean water in order to avoid any 

damages to the washer machine itself.

-  (pict.11)Release the gun safety catch and keep 

the trigger pressed, allowing the water to flow 

until all the air has been expelled.

-  (pict.8) Fit the lance into the gun.

-  Fit the nozzle  into the lance.

-  Connect the plug to the power socket.

>  1ST START-UP

When starting up for the first time or after a long 

period out of use, connect the intake line only 

for a few minutes so that any dirt is vented from 

the delivery outlet 

> START-UP

IMPORTANTE: 

(pict.12,13) Whenever using 

the high-pressure cleaner, users are urged to 

hold the gun in the correct position, with one 

hand on the grip and the other on the spray 

rod.

-  To start the machine, press the gun trigger 

and at the same time turn the master switch to 

“ON”

>  DETERGENT SUCTION

(pict.3, pos.

⑧

)  Fill up the detergent tank with 

the suggested products, suitable for the kind of 

washing to be carried out .

CORRECT USE OF THE MACHINE

-  The cleaner must be placed on a firm, stable surface and must be horizontal.

-  In case of operation indoors, adequate ventilation and gas venting must be assured.

-  Whenever using the high-pressure cleaner, users are urged to hold the gun in the correct position, with one 

hand on the grip and the other on the spray rod.

-  The water jet must never be pointed at the electrical cables or at the machine.

EN

20