BORT KEX-2500 93720100 - Инструкция по эксплуатации - Страница 6

6

NOTE:

 Test detergent in an inconspicuous area before 

use.

Figure 7 - Detergend application

UNITS WITH DETERGENT APPLICATOR 

INCLUDED

Follow manufacturer’s label directions for mixing correct 

concentrations of detergent to water ratio through the 

pressure washer is approximately 5.4% (1 to 19).

1. Unscrew to top of detergent applicator and fill applica

-

tor with detergent.

2. Replace top on applicator.

3. Remove lance from gun.

4. Attach detergent applicator to gun. ( See Figure 8)

Figure 8 - Attach applicator to gun

5. Apply detergent so it thoroughly covers cleaning sur-

face. Apply from bottom to top to prevent detergent from 

sliding down and streaking.

6. Allow detergent to remain on the surface for a few min-

utes. This is a good time to use a brush to lightly scrub 

heavily soiled areas.

Never allow detergent to dry on the cleaning surface.

7. Remove detergent applicator from gun and replace 

with the lance, or remove applicator from end of lance.

8. Rinse detergent from surface.

NOTE:

 Flush detergent applicator with clear water fol-

lowing each use.

4. Final Rinse

Start  final  rinse  at  bottom  an  work  upward.  Make  sure 

you thoroughly rinse the surface and that all detergent 

has been removed.

5. Shut down 

1. Be sure all detergent is flushed from system.

2. Turn off motor.

3. Turn off water supply.

4.  After motor and water supply are turned off, trigger gun 

to depressurize system.

CAUTION:

  NEVER  turn  water  supply  off  before  turning 

motor off. Serious damage could occur to the pump and 

or motor.

WARNING!

 NEVER disconnect high pressure discharge 

TURBO NOZZLE 

(NOT INCLUDED WITH ALL MODELS)

A turbo nozzle, sometimes referred to as a rotary nozzle, 

is a very effective tool that can significantly reduce clean

-

ing time. The turbo nozzle combines the power of a nar-

row high impact stream and the efficiency of a 25 degree 

fan pattern. This swirls the narrow high impact stream 

into a cone shape that cleans a larger area.

CAUTION:

 Since a turbo nozzle uses a narrow high im-

pact stream, only use it in applications where the clean-

ing surface cannot be damaged by narrow high impact 

spray. Additionally, the turbo nozzle is NOT adjustable 

and cannot be used to apply detergent.

DETERGENTS

The use of detergents can dramatically reduce cleaning 

time  and  assist  in  the  removal  of  difficult  stains.  Some 

detergents have been customized for pressure washer 

use on specific cleaning tasks. These detergents are ap

-

proximately as thick as water. The use of thicker deter-

gents, such as dish soap, will clog the chemical injection 

system and prevent the application of the detergent.

The cleaning power of detergents comes from applying 

them to a surface and giving the chemicals time to break 

down the dirt and grime. Detergents work best when ap-

plied at low pressure.

The combination of chemical action and high pressure 

rinsing  is  very  effective.  On  vertical  surfaces,  apply  the 

detergent starting at the bottom and work your way up-

ward. This will prevent the detergent from sliding down 

and causing streaks. High pressure rinsing should also 

progress from the bottom to top. On particularly tough 

stains, it may be necessary to use a brush in combination 

with detergents and high pressure rinsing.

OPERATION

The following cleaning procedure will help you to organ-

ize your cleaning task, and ensure that you achieve the 

most beneficial results in the shortest amount of time.

Remember to use the spraying/cleaning techniques pre-

viously listed.

1. Surface preparation

Before starting a pressure wash cleaning job, it is impor-

tant to prepare the surface that is to be cleaned. This is 

done by cleaning the area of furniture, and making sure 

that all windows and doors are closed tight. In addition, 

you should make sure that all plants and trees adjacent 

to the cleaning area are protected by a drop cloth. This 

will ensure that your plants won’t be sprayed by the de-

tergents.

2. Initial High Pressure Rinse

The next step is to spray the cleaning surface with water 

to clear off any dirt or grime that may have collected on 

the surface. This will allow your detergent to attack the 

deep down dirt that has worked its way into the clean-

ing surface. Before triggering the gun, adjust the nozzle 

to a wide fan pattern and slowly adjust to the desired 

spray pattern. This will help you avoid applying too much 

concentrated spray to the surface which could cause 

damage.

3. Detergent Application

USE THE INSTRUCTIONS APPROPRIATE FOR 

MODEL PURCHASED

NOTE:

 Use only detergents formulated for pressure 

washes.